valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. VIBRATION VIBRATION LEVEL 0.02g Vibration levels at the operators handles were measured in the vertical, lateral, and longitudinal directions using calibrated vibration test equipment. Tests were performed on 07/14/94 under the conditions listed: SOUND7 8 Sound tests conducted were in accordance with 2000/14/EEC and were performed on 04/13/2004 under the conditions listed: NOTE: Sound power level listed is the highest value for any model in this manual. Please refer to serial plate on the unit for the sound power level for your model. 120 dB WIND DIRECTION: HUMIDITY: TEMPERATURE: BAROMETRIC PRESSURE: GENERAL CONDITION: 30.10" Hg (765mm Hg) 62 % South East 16 MPH (25.7 kmh) 78° F (23.8° C) Sunny WIND SPEED: WIND DIRECTION: HUMIDITY: TEMPERATURE: BAROMETRIC PRESSURE: 30.18" Hg (767mm Hg) 39 % North West 0.5 MPH (0.8 kmh) 50.5° F (10.3° C) Sunny WIND SPEED: GENERAL CONDITION: (HTR1803VEU MODEL) Sound level of 94 dBA at operator position 21. DO NOT touch hot muffler, cylinder, or fins because contact may cause burns. 22. DO NOT run engine without air cleaner or air cleaner cover. 23. DO NOT operate during excessive vibration! 24. DO NOT leave machine unattended while in operation. 25. DO NOT park machine on a steep grade or slope. WARNING: DO 1. ALWAYS DO remove the wire from the spark plug when servicing the engine or equipment TO PREVENT ACCIDENTAL STARTING. 2. DO keep cylinder fins and governor parts free of grass and other debris which can affect engine speed. 3. DO pull starter cord slowly until resistance is felt. Then pull cord rapidly to avoid kickback and prevent hand or arm injury. 4. DO examine muffler periodically to be sure it is functioning effectively. A worn or leaking muffler should be repaired or replaced as necessary. 5. DO use fresh gasoline. Stale fuel can gum carburetor and cause leakage. 6. DO check fuel lines and fittings frequently for cracks or leaks. Replace if necessary 7. Follow engine manufacturer operating and maintenance instructions. 8. Inspect machine and work area before starting unit. aaaaaaaaaaaaa SAFETY INSTRUCTIONS GENERAL SAFETY ASSEMBLY PARTS BAG & CONTROLS LABELS OPERATION MAINTENANCE PARTS DRAWING & LIST TROUBLESHOOTING WARRANTY aaaaaaaaaaaaaaaaaaaaaaaaa TABLE OF CONTENTS 8 - 9 12 12 10 - 12 5 - 7 4 4 3 3 2 6 aaaaaaaaa Page 2 of 12 Part No. 811237 Form No. F050304A Part No. 811237 Page 3 of 12 Form No. F050304A For your safety and the safety of others, these directions should be followed: Use of Ear Protection is recommended while operating this machine. Do not operate this machine without first reading owner's manual and engine manufacturer's manual. Use of Eye and Breathing protection is recommended when using this machine, especially in dry and dusty conditions. ·DO NOT place hands or feet inside nozzle intake opening, near debris outlet or near any moving parts. ·DO NOT start engine without hose and exhaust elbow connected firmly in place to housing and exhaust outlet. GENERAL SAFETY PACKING CHECKLIST 9 Boxing Checklist Exhaust Elbow 811191 Boom Square Arm 810875 Check Boom Pivot WA 810870 Band Hose Boom 8" (203mm) 810880 Qty. 2 Coupler Weld Assy. 8"(203mm) 811170 Hose Clamps 8"(203mm) 810566 Qty. 2 Handle Nozzle 811020 Nozzle 8"(203mm) 811007 11 These items should be included in your carton. If any of these parts are missing, contact your dealer. 10 ASSEMBLY ·DO NOT operate without discharging exhaust into enclosed container. ·DO NOT operate during excessive vibration. ·DO NOT remove hose until engine has been turned off and has come to a complete stop. ·DO NOT operate machine with hose or exhaust elbow removed. ·DO NOT use this machine for vacuuming exclusively sand, dust, fine dirt, rock, glass, string like material, grain, rags, cans, metal, bark or water. ·DO NOT operate this machine on slopes greater than 20%. ·DO NOT pick up any hot or burning debris, or any toxic or explosive material. ·DO NOT allow children to operate this equipment. PUT OIL IN ENGINE BEFORE STARTING. Read all safety and operating instructions before assembling or starting this unit. Your Billy Goat is shipped from the factory in one carton and is completely assembled except for the exhaust elbow, nozzle, handle loop for nozzle, hose booms, hose bands, hose coupler, hose clamps and related hardware. 1. ASSEMBLE exhaust elbow (item 10), to main unit and firmly tighten knobs (item 90), that are preassembled to main unit. 2. SECURELY ATTACH unit to tailgate of a truck or to a trailer, so that the exhaust discharges into an enclosed container. 3. ATTACH hose to hose coupler (item 24), using hose clamp (item 60) NOTE: This unit is equipped with a unidirectional hose. Assemble hose so that interior hose material seams face toward unit. 4. ASSEMBLE hose coupler to housing of main unit and securely tighten knob (ite...