valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
PUT OIL IN ENGINE BEFORE STARTING READ all safety instructions before assembling unit. TAKE CAUTION when removing the unit from the box. Boxing Parts Checklist Exhaust Elbow Nozzle Tray Assembly Handle Loop Nozzle 811019 Handle Nozzle 811020 Hose Boom Assembly Nozzle QL 7901492 Hose Clamps 12" (305mm) 790150 Qty. 2 Band Hose Boom 12" (305mm) 790153 Qty. 2 Hose Coupler Assy Hose 12"x 10' QL 790148 Kohler command pro 23 HP Parts Bag & Literature Assy P/N 790297 PARTS BAG & LITERATURE ASSY Warranty card P/N- 400972, Owner’s Manual P/N-790294, Declaration of Conformity P/N-790162. Parts Bag Hardware Nut Lock 5/16-18 8160002 qty. 4 71 Handle Adj. W/Grip 811019 qty. 1 Rod Battery Hold Down 790231 qty. 2 71 66 Washer 5/16 SAE 8172008 qty. 2 Washer 5/16 Fender 8172020 qty. 4 68 Screwcap 1/4-20x 1 1/2 8041008 qty. 2 Nut Lock 3/8-16 8160003 qty. 4 Washer 3/8 FC 8171004 qty. 8 Bracket Battery QL 70 790230 qty. 1 60 85 For Mounting to a trailer Screwcap 3/8-16x2 3/4 8041057 qty. 4 65 Nut Lock 1/4-20 8160001 qty. 4 59 Screwcap 5/16-18x 1 1/2 52 8041030 qty. 4 Washer 1/4 SAE 8172007 qty. 6 NOTE: BATTERY IS NOT INCLUDED. REQUIRES 12 V BATTERY, 40 AH, 240 CCA MIN. U1 SERIES GROUP BATTERRY FOR PROPER FIT QL2300 Owner’s Manual ASSEMBLY OPERATION 1. SECURELY ATTACH unit to the bed of a truck or to a trailer, so that the exhaust discharges into an enclosed container. NOTE: This unit must be securely mounted to the bed of a truck or to a trailer before operating. 2. ATTACH hose to hose coupler, using hose clamp (item 26) NOTE: This unit is equipped with a unidirectional hose. Assemble hose so that interior hose material seams face toward unit. Refer to flow direction arrow printed on outside of hose. When installed arrow should point toward vac housing. 3. ATTACH hose coupler w/hose to housing intake, which is preassembled to housing front plate, and rotate to lock it in place. 4. ASSEMBLE handle loop nozzle (item 45), to nozzle handle (item 44) using capscrew (item 53), and lock nut (item 60). Adjust handle loop to desired height and angle and securely tighten in place. 5. ASSEMBLE nozzle handle (item 44), to nozzle (item 25), using screws (item 52), washers (item 66), washers (item 68) and lock nuts (item 60). 8. ATTACH assembled nozzle to hose using hose clamp (item 26). Before tightening hose clamp, position nozzle handle upward when hose is stretched to prevent twisting load on hose assembly during operation. 9. ATTACH preassembled hose boom on top of housing using a hitch pin (item 10). 10. ASSEMBLE hose band (item 29) around hose and secure chain between flanges of the hose band using capscrew (item 53) and lock nut (item 60) Repeat same steps on the other chain. (See ADJUSTING HOSE BOOM on page 11). 11. SECURELY ATTACH exhaust elbow (item 21) capturing both flanges inside the clamp, then firmly tighten the clamp, securing the elbow to the housing (see MOUNTING on page 10). 12. ASSEMBLE battery (not included) by using battery bracket QL (item no. 70, hold down rods (item 71), washers (item 70), and lock nuts (item 59). 13. ATTACH red battery cable to + terminal and black battery cable to - terminal. QL2300 Owner’s Manual ASSEMBLY OPERATION 1. SECURELY ATTACH unit to the bed of a truck or to a trailer, so that the exhaust discharges into an enclosed container. NOTE: This unit must be securely mounted to the bed of a truck or to a trailer before operating. 2. ATTACH hose to hose coupler, using hose clamp (item 26) NOTE: This unit is equipped with a unidirectional hose. Assemble hose so that interior hose material seams face toward unit. Refer to flow direction arrow printed on outside of hose. When installed arrow should point toward vac housing. 3. ATTACH hose coupler w/hose to housing intake, which is preassembled to housing front plate, and rotate to lock it in place. 4. ASSEMBLE handle loop nozzle (item 45), to nozzle handle (item 44) using capscrew (item 53), and lock nut (item 60). Adjust handle loop to desired height and angle and securely tighten in place. 5. ASSEMBLE nozzle handle (item 44), to nozzle (item 25), using screws (item 52), washers (item 66), washers (item 68) and lock nuts (item 60). 8. ATTACH assembled nozzle to hose using hose clamp (item 26). Before tightening hose clamp, position nozzle handle upward when hose is stretched to prevent twisting load on hose assembly during operation. 9. ATTACH preassembled hose boom on top of housing using a hitch pin (item 10). 10. ASSEMBLE hose band (item 29) around hose and secure chain between flanges of the hose band using capscrew (item 53) and lock nut (item 60) Repeat same steps on the other chain. (See ADJUSTING HOSE BOOM on page 11). 11. SECURELY ATTACH exhaust elbow (item 21) capturing both flanges inside the clamp, then firmly tighten the clamp, securing the elbow to the housing (see MOUNTING on page 10). 12. ASSEMBLE battery (not included) by using battery bracket QL (item no. 70, hold down rods (item 71), washers (item 70), and lock nuts (item 59). 13....