valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
To prevent feedback, do not take the Parent unit into the nursery/baby's room. Do not Press Talk button when the Baby unit and Parent unit are positioned in the same room. Feedback will be generated if the talk button is pressed when the Baby unit and Parent unit are to close to each other. 8 OpErATING ThE pArENT UNIT 5 Operating the Parent Unit Switching the parent unit on/off TURN ON - Press and hold this button until you hear 2 beeps. The Oricom logo appears then the image being taken by the baby unit camera will appear. TURN OFF - Press and hold this button for approx. 1 second to switch the unit off. Adjustable Volume Use this button to adjust the volume to one of five settings. The volume levels will be adjusted on both the baby unit and parent unit simultaneously. NOTE: The volume cannot be turned OFF. Setting the brightness Press this button once. This icon appears in the display for a few seconds. Use these buttons to adjust the brightness to one of five settings. Adjusting the temperature Indicator IMPORTANT INFORMATION The parent unit has an in-built temperature sensor which is not as accurate as a medical thermometer. It only measures the temperature at the specific point it is located. The measurement range of the sensor is 0 - 40 degrees C. Temperature Display Your monitor is pre-set to display the temperature measured in Centigrade, should you wish to change it, follow the steps below: Press this button twice. This icon appears in the display for a few seconds. Use this button to set temperature indicator to OFF, °C or °F. The temperature that is measured by the Baby unit is displayed on the parent unit e.g. in °C. Turning the night light on/off Press this button three times. This icon appears in the display for a 15 seconds. Use this button to turn the night light on the baby unit on or off. OpErATING ThE pArENT UNIT 9 Adjusting the VOX1 sensitivity VOX1: Voice Operated Transmission = Sound detection The VOX1 function (sound detection) causes the system to start transmitting automatically from the baby unit to the parent unit only when sound is detected. Press this button four times. This icon appears in the display for a few seconds. Use this button to set VOX to OFF or adjust the sensitivity to one of 5 levels. When one of the five levels has been set, the VOX LED lights up red and the display goes out after 10 seconds. Red VOX LED light illuminates to indicate VOX is turned ON. NOTE: VOX will not activate if lullabies are turned ON. The display is reactivated when a sound is detected or a button on the parent unit is pressed. Selecting a lullaby Press the button on the right hand side of the parent unit to turn lullabies ON/OFF. This icon appears in the display. Use the button to select one of the 5 lullabies (1-5). If no number is displayed, all of the lullabies will continue to play in sucession until deactivated. Use this button to adjust the volume to one of five settings. The volume levels will be adjusted on both the baby unit and parent unit simultaneously. This icon appears during the volume adjustment. NOTE: The volume cannot be turned OFF. Lullabies will continue to play on the Baby Unit when the Parent unit is turned OFF. To turn off the lallabies on the baby unit turn parent unit back ON. Intercom function Press and hold this button to talk. Release button when you have finished speaking. This icon appears on the display. Speak into the microphone to talk to the person near the room being monitored. When you press intercom function lullabies will be deactivated. Range This icon flashes in the display and a tone will be heard when the distance between the baby unit and parent unit is too great. Move the parent unit nearer to the baby unit. 10 OpErATING ThE pArENT UNIT Power failure/portable use In the event of a power failure or for portable use when no mains power is available, the Baby unit will require charged Alkaline batteries (not supplied) to operate. Note: When using Alkaline batteries the unit will only operate for a short period (up to 4 hours depending on the quality of the batteries used.). Installing Alkaline batteries Ensure AC adaptor is not connected to the baby unit. Use a small screwdriver to open the battery door on the base of baby unit. Insert the 4 AAA batteries (not supplied), paying attention to the correct polarity. Refer to the diagrams in the battery compartment. Replace the battery compartment and fit screw. In the case of a low battery, the Power LED on the baby unit flashes slowly. The batteries must be replaced. Registration The parent unit and baby unit are pre.registered. If necessary, registration can be completed manually: Baby unit/Parent unit 1 Switch the baby unit and parent unit off. 2 Cover the light sensor with a dark cloth and switch the baby unit on. Position ON. 3 The Power LED on the baby unit flashes quickly for approx. 15 seconds. 4 Switch the parent unit on and wait until the Oricom logo disappears from the display and then press ...