valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
Turn the spindle to the left until it clicks in position. Disconnecting the neck strap • Turn the spindle to the right (TURN 2) and take it off. Paging parent unit When the parent unit is misplaced and the volume is switched off, you can use the PAGE button (A-6) on the baby unit to locate the parent unit. 1 Briefly press the PAGE button (A-6) on the baby unit. > A paging alert will sound on the parent unit. 2 To stop the paging alert, briefly press the page button (A-6) again or any button on the parent unit. Note: If you press the PAGE button (A-6) too long, the paging alert will not sound. Troubleshooting EN Problem Possible cause Solution LINK light (A-2, B-7) does not light at all. Parent unit: Power adapter (B-13) not plugged in. Connect power adapter (B-13) to parent unit. Connect power adapter (B-13) to wall outlet. Unit not turned on. Press and hold On/Off button (y) (B-5) for two seconds. Batteries are low. Recharge batteries (B-11). Batteries are empty. Replace batteries (B-11). Baby unit: Power adapter (A-11) not plugged in. Connect power adapter (A-11) to baby unit. Connect power adapter (A-11) to wall outlet. Batteries incorrectly inserted. Insert batteries correctly. Unit not turned on. Press and hold On/Off button (y) (A-1) for two seconds. Batteries are low. Replace batteries (A-9). LINK light (A2, B-7) flashing red/alarm beeping on parent unit. Units out of range. Baby unit batteries are low. Decrease distance between units (see ‘Technical specifications). Replace batteries (A-9.). Parent unit batteries are low. Recharge batteries (B-11). Parent unit batteries are empty. Replace batteries (B-11). Units cannot establish connection, even when close to each other. Try solving the problem by using the factory initialization mode. See chapter ‘Factory initialization mode’. No power on one of the units. Press On/Off button (A-1, B-5) for two seconds. EN Troubleshooting Problem Possible cause Solution High pitched noise. Units are too close to each other. Move parent unit away from baby unit (at least 1 meter / 3 feet). Volume on parent unit set too high. Decrease volume (B-9) on parent unit. No sound/ baby’s crying cannot be heard. Volume on parent unit is set too low or switched off. Microphone sensitivity level set too low on parent unit. Increase volume on parent unit (B-9). Adjust microphone sensitivity level (B-2) on parent unit. to a higher level. Units are out of range Move parent unit closer to baby unit. Parent unit reacts too fast to other ambient sounds. Ambient sounds trigger transmission. Move baby unit closer to baby (keep minimal distance of 1 meter / 3 feet). Microphone sensitivity set too high. Decrease microphone sensitivity level (B-2) on parent unit. Parent unit reacts slowly/ late to baby's crying. Microphone sensitivity is set too low. Increase microphone sensitivity level (B-2) on parent unit and/or move baby unit closer to baby (keep minimal distance of 1 meter / 3 feet). Battery check light ( is lit. ) Batteries are low or almost empty. Replace batteries (A-9, B-11). Baby unit battery power diminishes rapidly. Microphone sensitivity is set too high. Unit consumes more power. Set microphone sensitivity to a lower level (B-2). Volume setting too high. Set volume to a lower level (A-4). Charging time of parent unit batteries exceeds 16 hours. Parent unit switched on during charging. Switch off parent unit (B-5). Frequently asked questions EN Question Answer The technical specifications show an operating range of 300 meters / 900 feet outdoors. How come my baby monitor manages much less than that? The specified range is only valid outdoors in open air. Inside your house the workable range is limited by the amount and type of walls and/or ceilings in between. Inside the house the operating range will be up to 50 meters / 150 feet. The link is lost every now and then, sound interruptions etc. You are probably approaching the outer limits of the practical range. Try a different location or decrease the distance slightly. Please note that it takes about 30 seconds each time before a new link between the units is established. What happens during a mains failure? When batteries are installed in the both units, the units will automatically switch over to battery use in case of mains failure. Is my DECT baby monitor secure from eavesdropping and interference? The 120 channels guarantee no interference from other equipment. Some buttons do not seem to work when I press them. What do I do wrong? Except for the On/Off buttons and TALK button (A-1, B-5), only press the buttons briefly. Operating time of the parent unit batteries is supposed to be at least 8 hours. How come the battery operating time of my parent unit is less? When the parent unit batteries are charged for the first time, operating time will be less than 8 hours. The batteries will use their maximum capacity after at least four times charging and discharging. Maybe the volume setting is too high. When the volume is set t...
Questo manuale è adatto anche per i modelli :Baby - SCD488/84 (1.82 mb)