|
Facilità d'uso
The units may be too close to each other. Make sure the parent unit and the baby unit are at least 1 metre/3 feet away from each other. The volume of the parent unit may be set too high. Decrease the volume of the parent unit. The volume of the parent unit may be set too low or may be switched off.Turn the volume wheel to a higher volume level. Perhaps you have switched on the automatic screen activation. If the automatic screen activation is activated, the video display only switches on when the baby unit picks up a sound. As long as no sound is detected, the video display is off to save power. The baby unit also picks up other sounds than those of your baby. Move the baby unit closer to the baby (but obser ve the minimum distance of 1 metre/3 feet). Perhaps you have switched on the nightlights. If you want to use the nightlights, we advise you to use the baby unit corded. Perhaps you are playing lullabies.The baby unit consumes a lot of energy when you play lullabies. If you play lullabies, we advise you to use the baby unit corded. The parent unit may be switched on during charging. Switch off the parent unit during charging. EngliSh 17 QuestionAnswerThe specified operating range of the baby monitor is 150 metres/490 feet. Why does my baby monitor manage a much smaller distance than that? The specified range is only valid outdoors in open air. Inside your house, the operating range is limited by the number and type of walls and/or ceilings between the parent unit and the baby unit. Why can’t I establish a connection? Why is the connection lost ever y now and then? Why are there sound interruptions? What happens during a power failure? The operating time of the parent unit is supposed to be at least 6 hours. Why is the operating time of my parent unit shor ter? Why do I get interference on the parent unit? Why does the parent unit make a buzzing sound? The baby unit and the parent unit are probably close to the outer limits of the operating range or there is interference from other 2.4GHz wireless devices.Tr y a different location, decrease the distance between the units or switch off other 2.4GHz wireless devices. Please note that it takes about 5 seconds each time before a connection between the units is established. If the parent unit is sufficiently charged, it continues to operate during a power failure. If there are batteries in the baby unit, it also continues to operate during a power failure. When the parent unit has been charged for the first time, the operating time is shor ter because the batter y has not reached its full capacity yet. The rechargeable batter y only reaches its full capacity after you have charged and discharged it at least four times. After this, the operating time is 6 hours if the automatic screen activation is not activated and 8 hours if the automatic screen activation mode is activated. The parent unit consumes a lot of energy when the video display is switched on continuously. Activate the automatic screen activation mode to increase the operating time (see chapter ‘Features’, section ‘Automatic screen activation’). The volume of the parent unit may be set too high, which causes the parent unit to consume a lot of energy. Decrease the volume of the parent unit Interference may occur when the parent unit is out of range of the baby unit. Interference may also occur if there are too many walls or ceilings between the parent unit and the baby unit or when other 2.4GHz wireless devices are switched on (e.g. microwave, internet). Put the parent unit in a different place, closer to the baby unit, or switch off other wireless devices. Interference may occur when the parent unit is out of range of the baby unit. Interference may also occur if there are too many walls or ceilings between the parent unit and the baby unit or when other 2.4GHz wireless devices are switched on (e.g. microwave, internet). Put the parent unit in a different place, closer to the baby unit, or switch off other wireless devices. The rechargeable batter y of the parent unit may need to be charged. 18 EngliSh QuestionAnswer Why does the video display flicker? Why isn’t there any image on the video display when the power- on light is on? Why isn’t the image on the video display clear? Why doesn’t the parent unit work in the automatic screen activation mode? Why isn’t the image on the video display clear in night vision? Why doesn’t the batter y symbol appear on the video display of the parent unit when I star t to charge the parent unit? Why doesn’t the parent unit charge when I have plugged it in? Interference may occur when the parent unit is out of range of the baby unit. Interference may also occur if there are too many walls or ceilings between the parent unit and the baby unit or when other 2.4GHz wireless devices are switched on (e.g. microwave, internet). Put the parent unit in a different place, closer to the baby unit, or switch off other wireless devices. The rechargeable batter y of the parent ...
Questo manuale è adatto anche per i modelli :Baby - SCD600/10 (1.51 mb)