valutazioni - 3, GPA: 5
(
)
)
|
Facilità d'uso
Lock and arm/unlock and disarm. May be programmed to unlock driver's door or all doors. Also will initiate and terminate *Panic. Pulsed or switched output to control Remote Trunk Release or optional device connected to channel 3. When pressed and release two times, will provide pulsed output or activate the Remote Start option when installed. When so equipped, this button can be used to operate an optional device connected to channel 4. When so equipped, this button can be used to operate an optional device connected to channel 5. These transmitters make use of icons (symbols) to identify the reaction your security system/keyless entry/and or remote start system, where applicable, will have when any icon (button) is pressed. These icons are programmed at time of installation to meet the needs of the individual and to complement the vehicle that the system is installed in. To replace a transmitter or add transmitters, please follow the programming instructions listed on the pages of this manual. Transmitter Programming Guide Model 105BP 1 2 1 3 3 *4 *5 BUTTON RECEIVER CHANNEL SYSTEM FUNCTION Lock And Arm Alarm, also initiate and terminates *Panic Unlock And Disarm, also initiates and terminates *Panic. Programmable to unlock drivers door and or all doors. Lock and arm/unlock and disarm. May be programmed to unlock driver's door or all doors. Also will initiate and terminate *Panic. Pulsed or switched output to control Remote Trunk Release or optional device connected to channel 3. When pressed and release two times, will provide pulsed output or activate the Remote Start option when installed. When so equipped, this button can be used to operate an optional device connected to channel 4. When so equipped, this button can be used to operate an optional device connected to channel 5. These transmitters make use of icons (symbols) to identify the reaction your security system/keyless entry/and or remote start system, where applicable, will have when any icon (button) is pressed. These icons are programmed at time of installation to meet the needs of the individual and to complement the vehicle that the system is installed in. To replace a transmitter or add transmitters, please follow the programming instructions listed on the pages of this manual. Transmitter Programming Guide Model 105BP * Where So Equipped 128-8777 1 of 8 PROGRAMMING TRANSMITTERS: NOTE: It is important to remember that during the programming mode, each individual step must be completed within 15 seconds ofthe previous step. If the 15 second time limit expires betweensteps, the unit will automatically exit the program mode. Thisis indicated by a long chirp from the siren. Non alarm models will flash the parking lights only to confirm the transmitter code has been learned and stored. NOTE: Because the system may be capable of sounding a siren, thevehicle horn, or both, where the siren chirp is referenced below, the siren may chirp, the horn may beep, or both devicesmay sound. NOTE: Some systems are capable of single button programming, if youralarm module is capable of this feature, simply complete step 4of these programming instructions for each transmitter you wishto control your system and exit the program mode by switchingoff the ignition key. TO PROGRAM ADDITIONAL TRANSMITTERS: 1) Enter the vehicle, and turn the ignition switch to the on position. 2) Press and release the valet push-button switch three times. NOTE: Some systems may use a combination push-button LEDswitch. In these systems the push-button and the dash- mounted LED are one and the same. 3) The dash mounted LED will flash 1x, and the siren will chirp 1x, indicating that the system is ready to accept programming of channel#1 which is arm/lock, disarm/unlock/unlock 2, and panic functions. 4) Press and hold the lock or lock/unlock symbol button of the transmitter you wish to program for 4 seconds or until a long chirp is heardfrom the siren. "Repeat step 4 for each transmitter you wish to program". NOTE: If your transmitter button has the Lock/Unlock icon on onebutton, press and release the valet push button switch 2 timesthen move on to step #8.5) Press and release the valet push button switch one time to advance tochannel 2. The siren will chirp 2 times and the dash-mounted LED willFlash 2 times, indicating that the unit is ready to accept programmingfor channel # 2 which is only used for separate lock and unlockbutton transmitters, and is the disarm/unlock/unlock 2 and panic. 6) Press and hold the unlock symbol button of the transmitter you wishto program for 4 seconds or until a long chirp is heard from thesiren. "Repeat step 6 for each transmitter you wish to program". 7) Press and release the valet push button switch one time to advance to channel 3. The siren will chirp 3 times and the dash 2 128-8777 2 of 8 mounted LED will Flash 3 times, indicating that the unit is readyto accept programming for channel # 3 which is the trunk release/ alternate output channel of the sy...