valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
...... ...... About Station Presets The Solo has 20 station presets. The presets can be used to store either AM or FM stations. Because of the way the Solo places stations in the presets you may want to plan how you store them. Here’s how it works. The first station you store goes into Preset 1. The second station goes into Preset 2 and so on, up to 20 stations. If you remove a preset all the stations in presets above the one you removed, drop down a preset position. The table below gives an example. Preset # 1 2 3 4 5 6 7 originally programmed stations FM 89.7 FM 90.9 FM 100.3 FM 104.9 AM 680 AM 850 AM 1030 after removing presets 2 and 6 FM 89.7 FM 100.3 FM 104.9 AM 680 AM 1030 It may be helpful to put the presets in some logical order. You could put the FM presets in order of ascending frequency. For example put 89.7 into Preset 1, 90.9 into Preset 2, 93.7 into Preset 3, etc. Or you could assign presets on the basis of how often you listen to them. For example, your favorite station could go into Preset 1, the next favorite into preset 2, etc. Turn the MODe control to select Preset. Turn the tune control to select the preset station you want. The Preset indicator, the preset number and the station frequency will light. Tuning in a Preset Station 12 In this example AM preset 5, with station frequency 1050 assigned to it, has been selected. .... Removing One or More Presets To remove one preset – Tune in the preset station as described above. Press and hold the tune control. When the Preset has been cleared the station frequency, “radio” and the AM/FM band indicator are replaced with “_ _ _ _” . Note: You must tune in the preset you want to delete with the Preset source. If you tune in a radio station that has been placed in a preset using the AM or FM source, you will see the Preset indicator and number in the display, but you will not be able to delete the preset. To clear all the presets – Using the Preset source, tune in any preset station. Then press and hold the tune control for 10 seconds. You’ll hear 3 beeps indicating the presets have been cleared. Alarm Clock Features The Horizon Solo has two independent alarm settings. Each can have its own type of alarm—wake to tone, wake to music or both. Both types of alarms start at a low volume level that gently increases. Setting the Alarm Time The alarm time can be set when the Solo is turned on or off. 1 23 Press and hold the alarM 1 or alarM 2 button for one second. The alarm time and the or icon will flash. Turn the MODe control to adjust the alarm time. Press the MODe control to set the alarm time. ........ In this example Alarm 2 is set to 7:15 AM. Note: The alarm time can also be set by using the MODe control to highlight the or icon. Then press the MODe control and follow steps 2 and 3 above. .... .... Setting an Alarm If you plan to use the wake to music function, note that the last source and volume level settings will be used for the alarm. 1 Press the alarM 1 or alarM 2 buttons one or more times to turn on the alarm and set the alarm type. One press .. selects wake to music . A second press selects wake to tone . A third press selects both. Press the button a fourth time to cancel the alarm. Press the pOwer/VOluMe button to turn the Solo off. The display will show the current time along with the icons for the alarm(s) and alarm style(s) selected. 2 This example shows how the display might look after the Solo is turned off. The current time is displayed and the icons show Alarm 1 is on, set for wake to music and tone, and Alarm 2 is on, set to tone only. How the Alarms Work When an alarm starts the icon for the alarm starts flashing. If you selected wake to tone the alarm tone starts sounding, quietly at first then with increasing volume. If you selected wake to music the radio station that was tuned in when you set the alarm is played at a gradually increasing volume. If you selected wake to music and tone the radio station that was tuned in when you set the alarm is played at a gradually increasing volume. If you do not turn off the alarm within five minutes the music stops playing and the alarms tone begins to sound at a gradually increasing volume. To turn off the alarm press the pOwer/VOluMe button. The Snooze Feature If you want to sleep a while longer after the alarm sounds you can use the “Snooze “ feature. Simply touch the metal rim around the front of the Solo. This delays the alarm for ten minutes. Each additional touch of the rim increases the length of the “Snooze” alarm delay by 5 minutes. The maximum delay is 60 minutes. The display shows the time and a flashing Alarm icon. Touch Sensitive Rim To see how much “Snooze” time is left touch the metal rim once. If you touch the rim again another five minutes is added to the “Snooze” time for each additional touch. To cancel the “Snooze” function press the button for the active Alarm. Sleep Function You can set the Horizon Solo to play for up to 90 minutes. After the specified time the S...