valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
alkaline with carbon zinc. Only use batteries of the same type for the set. • When inserting new batteries, do not tr y to mix old batteries with the new ones. • Remove the batteries if the set is not to be used for a long time. Batteries contain chemical substances, so they should be disposed of properly. Power Supply General Information Using AC power 1 Check if the power voltage, as shown on the type plate located on the rear of the set, corresponds to your local power supply. If it does not, consult your dealer or ser vice center. 2 Connect the supplied switching adapter to the wall socket and the DC jack on the set. The set is now ready to use. 3 To switch the set off completely, withdraw the power cord from the wall socket. • Install the unit near the AC outlet and where the power plug can be easily reached. • Disconnect the power cord from the wall socket to protect your set during heavy thunderstorms. • AC power cord is used as the disconnect device. It shall remain readily operable and should not be obstructed during intended use. To be completely disconnected the apparatus from supply mains, the power cord of the apparatus shall be disconnected from the mains socket outlet completely. The type plate is located on the rear of the set. General information Antennas • For FM, extend, incline and turn the telescopic antenna for best reception. Reduce its length if the signal is too strong. • For MW, the set uses a built-in antenna. Direct this antenna for best reception by turning the whole set. Connecting earphones • You can connect headphones to the headphone socket. . The loudspeakers will then be switched off. DBB sound effect You can enhance bass by enabling DBB sound effect. • To enable or disable DBB sound effect, press DBB/SET TIME repeatedly. . DBB appears when DBB sound effect is enabled. Basic Operation Radio Basic operation 1 Connect the supplied switching adapter to the wall outlet and the DC jack on the set or inser t batteries as described in Power Supply. . The clock information is displayed. (See 2) • Press 2 to switch on the set. • Press 2 again to switch to standby mode. 2 To adjust volume, turn VOLUME +/–. Helpful hints: – When there is no power supply for the set, time information can still be displayed for a few minutes. – After a few minutes, appears and flashes and then time information is cleared. Resetting to the factory setting 1 Press and hold DBB/SET TIME and TIMER at the same time when connecting the set to AC power supply or inserting batteries. . The software version is displayed. . The set enters testing mode. 2 To reset, press POWER. . All icons are displayed on the LCD display. . . The set is reset. Switching on radio 1 Press 2 to switch on the set. 2 Press SOURCE to select FM or MW wave band. . Waveband and radio frequency are displayed (see 3 and 4). Auto tuning 1 In FM/MW mode, press and hold MEMORY/ AUTO SCAN until SCAN appears. . The set scans stations with strong signal strength and stores them as preset stations automatically. 2 Press TUNING +/-and hold it for one second; the set searches a station automatically. . Sr ch appears. . When a station is received, search stops and Sr ch disappears. Helpful hints: – You can press any button except power to exit auto search. Manual tuning By using this feature, it is possible to manually tune to a specific channel frequency. In addition to antenna orienting for better radio reception, the optimum reception can also be obtained by using this feature. 1 In FM/MW mode, press TUNING +/-to tune to stations. 2 Press and hold TUNING +/-to adjust frequency fast. Radio Clock/Timer Storing preset stations You can store up to 10 FM stations and 10 MW stations respectively on PRESET for easy access. 1 In FM/MW mode, tune to your desired radio station (See "Auto tuning" and “Manual tuning”). 2 Press MEMORY/AUTO SCAN once, and then turn VOLUME +/-to select preset numbers. 3 Press MEMORY/AUTO SCAN once to store the preset station. Helpful hints: – If you have already saved a FM or MW station in that preset number, it will be overwritten by a new station. – Preset FM stations and MW stations do not overwrite each other. Selecting a preset station 1 In FM/MW mode, press PRESET repeatedly until your desired station is displayed. 2 Press and hold PRESET to switch between stations fast. Setting time You can only set time in standby mode. 1 Press and hold DBB/SET TIME until hour digit flashes. 2 Turn VOLUME +/-to set hour. 3 Press DBB/SET TIME once to confirm . The minute digit flashes. 4 Turn VOLUME +/-to set minute. 5 Press DBB/SET TIME once to confirm. . The set exits time setting. Helpful hints: – During setting time, if you press any other button or do not operate for more than 10 seconds, the set automatically exits time setting. Setting timer You can only set timer in standby mode. 1 Press and hold TIMER until ON appears and hour digit flashes. 2 Turn VOLUME +/- to set hour. 3 Press TIMER once to confirm . Minute digit flashes. 4 T...