valutazioni - 4, GPA: 3.8
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
Compatible transceivers include: • TS-2000(X) • TS-570S/ 570D • TS-850S • TS-870S • TS-690S • TS-950SDX • TS-450S Data Transfer could be useful while contesting. A spotting station that is searching for new contest multipliers can quickly transfer a frequency over to the running (main) station. SETTING UP ¦ Equipment Needed In addition to a compatible transceiver, the following equipment is required: Transfer to TS-2000(X), TS-570, or TS-870S: • One cross-wired cable. This cable must have a 9-pin RS-232C female connector at both ends. Transfer to a transceiver other than TS-2000(X), TS-570, and TS-870S: • KENWOOD IF-232C interface unit. • One cross-wired cable. This cable must have a 9-pin RS-232C female connector at one end and a 25-pin RS-232C female connector at the other end. • One straight cable. This cable must have a 6-pin DIN male connector at both ends. ¦ Connections For diagrams on how to connect the two transceivers, see “CONNECTING PERIPHERAL EQUIPMENT” {page 93}. Note: If you are using a DSP-100 unit with the transceiver, turn on the transceiver first, then turn on the DSP-100. USING QUICK TRANSFER When connecting with another TS-2000(X), TS-570, or TS-870S, use the same COM connector baud rate on each transceiver. If transferring to or from other KENWOOD transceivers, select 4800 bps and 2 stop bits. On the TS-2000(X), set the parameter in Menu No. 56 to 4800 bps. Note: While transferring data, other functions may work slower. ¦ Transferring Data The TS-2000(X) transceiver works as the Master, sending data to the Slave transceiver. 1 Switch ON the Transfer function of each transceiver. • On the TS-2000(X), access Menu No. 52 and select ON. For the compatible transceiver, refer to the instruction manual that came with the transceiver. 2 On the Master, while in VFO mode, select an operating frequency and mode. 3 On the Master, press QUICK MEMO [M.IN]. • When using another TS-2000(X) as the Slave, “PC” appears on the Slave. • The displayed data is stored in Quick memory channel 0 on the Master and transferred to the Slave. Note: If the Master has RIT switched ON, the offset frequency is added to the receive frequency to be transferred. ¦ Receiving Data The TS-2000(X) transceiver works as the Slave, receiving data from the Master transceiver. The Slave can receive data using either Quick memory channel 0 or the VFO. 1 Switch ON the Transfer function of each transceiver. • On the TS-2000(X), access Menu No. 52 and select ON. For the compatible transceiver, refer to the instruction manual that came with the transceiver. 2 On the Slave, access Menu No. 53 and select either OFF (QUICK MEMO channel 0) or ON (the VFO). • The default is OFF (QUICK MEMO). 3 On the Master, perform the appropriate operation to send data. • For the correct method, refer to the instruction manual that came with the transceiver. Note: . If you always use the TS-2000(X) for receiving only, activate the TX Inhibit function, accessing Menu No. 54 to avoid unintentional transmission. . When the Slave receives data using the VFO programmed with a simplex frequency, the received data replaces the data on both VFOs. On the Slave, both RIT and XIT are set to OFF. . When the Slave receives data using the VFOs programmed with split frequencies, the received data replaces the data only on the TX side of the VFO. On the Slave, XIT is set to OFF but RIT is not changed. 15 OPERATOR CONVENIENCES COMPUTER CONTROL By connecting this transceiver to a computer, you can change the computer into an electronic console from which you can remotely control functions of the transceiver. This capability makes remote operation of your transceiver possible from across the room, from another room, or when coupled with other commercially available products and where lawful, from another city, state, or country via a telephone connection. Note: . You can use the front panel controls while using computer control. Settings done from the front panel are effective immediately. . After the computer is disconnected or turned off, all values and settings on the front panel are restored. SETTING UP ¦ Equipment Needed • A PC equipped with an RS-232C serial port. • One straight cable. This cable must have a 9-pin D-Sub RS-232C female connector at one end, and at the other end a 9-pin or a 25-pin D-Sub RS-232C female connector that mates with the RS-232C port of your computer. • Transceiver control application. To design your programs, consult “APPENDIX” for the necessary information. ¦ Connections Connecting the transceiver to the computer is easy. See the diagram given in “CONNECTING PERIPHERAL EQUIPMENT” {page 93}. Note: Before connecting this transceiver to the computer, switch OFF the power to both the transceiver and the computer. COMMUNICATION PARAMETERS In order to control the transceiver by computer, you must first choose the communication parameters. 1 On the computer, configure your transceiver control application for 8 data bits, 1 stop bit and no parity. 2...
Questo manuale è adatto anche per i modelli :Radio - TS-2000 (2.76 mb)
Radio - TS-2000X (2.76 mb)