valutazioni - 1, GPA: 4
(
)
)
|
Facilità d'uso
11): Operation Approx. battery life While in use (TALK) near the base unit* 8-9 hours away from the base unit 3-4 hours While not in use (Stand-by) 14 days 'Within about 10 feet (3 m) • Battery life may be shortened depending on usage conditions, such as viewing the Caller ID Caller List or directory items, and ambient temperature. • Clean the handset and the base unit charge contacts with a soft, dry cloth once a month. Clean more often if the unit is subject to grease, dust or high humidity. Otherwise the battery may not charge properly. • If the battery is fully charged, you do not have to place the handset on the base unit until “Recharge” is displayed and/or “I I ]” flashes. This will maximize the battery life. • The battery cannot be overcharged. Stand-by mode {The handset is off the base unit.) The handset goes into the stand-by mode after you finish using the handset (making/answering a call, viewing the Caller List or directory items etc.). The display is blank, but the handset can receive calls. The battery life is conserved in this mode. 12 Using the Belt Clip You can hang the handset on your belt or pocket using the belt clip. To attach the belt clip To remove the belt clip Using the Optional Headset Plugging the optional headset into the handset allows a hands-free phone conversation. Please use only a Panasonic KX-TCA80 or KX-TCA90 headset. To order, call the accessories telephone number on page 2. Connecting an headset to the handset Open the headset jack cover, and connect the headset to the headset jack as shown below. The illustration headset is a KX-TCA90. Headset Jack When the optional headset is connected to the handset, be sure to use the headset to talk with the caller. If you want to have a normal cordless phone conversation, disconnect the headset. 13 Preparation ^ Settings Selecting the Dialing Mode You can program the dialing mode using the handset near the base unit. If you have touch tone service, set to “Tone”. If rotary or pulse service is used, set to “Pulse”. Your phone comes from the factory set to “Tone”. Make sure that the handset is in the stand-by mode. 1 2 3 4 5 6 Press I FUNCTION/EDIT]. Press ® or [a) repeatedly until the arrow points to “Program”. Press OK (►) (Yes key). Press ® or ® repeatedly until the arrow points to “Set dial mode”. ►Redial Directory va OK=Yes Ringer volume ►Program va OK=Yes ►Save directory Set flash time va OK=Yes Set line mode ►Set dial mode va OK=Yes Press OK (►) (Yes key). Dial mode : Tone va OK=Save Press ® or ® to select “Pulse” or Dial mode “Tone”. Press OK (►) (Save key). : Pulse • A beep sounds. • The display will return to the function list. To return to the stand-by mode, press lEXIT/CH) or wait for 60 seconds. • You can exit the programming mode any time by pressing IEX1T/CHI. • If 3 beeps sound and the display shows “Save error”, move closer to the base unit and try again. If “Save error” is still displayed, place the handset on the base unit. Start again from step 1. If a power failure occurs, the mode will return to the factory preset (Tone). Reprogram if necessary. 14 Selecting the Line Mode If the line is connected to a low voltage system such as a PBX, set to “B”. Otherwise the unit may not ring and the Visual Call Waiting (Call Waiting ID) Service may not be accessible (p. 46). Your phone comes from the factory set to “A”. Make sure that the handset is in the stand-by mode. 1 Press I FUNCTION/EDIT). O Press ® or ® repeatedly until the arrow points to “Program”. 0 Press OK (►) (Yes key). Press © or (X) repeatedly until the arrow points to “Set line mode”. Press ® or ® to select “b" or “a”. Press OK B (Save key). • A beep sounds. • The display will return to the function list. To return to the stand-by mode, press [EXlT/CHl or wait for 60 seconds. ►Redial Directory va OK=Yes Ringer volume ►Program va OK=Yes ►Save directory Set flash time va OK=Yes ►Set line mode Set dial mode va OK=Yes Line mode : A VA OK= Save Line mode : B • You can exit the programming mode any time by pressing IEXIT/CHl. • If 3 beeps sound and the display shows “Save error”, move closer to the.base unit and try again, if “Save error” is still displayed, place the handset on the base unit. Start again from step 1. If a power failure occurs, the mode will return to the factory preset (A). Reprogram if necessary. 15 Preparation Programmable Functions You can program the following function items using the handset near the base unit. The display shows the programming instructions. See the corresponding pages for the function details. Make sure that the handset is in the stand-by mode. Press I FUNCTION/EDITl. »