KX-TGA230B/KX-TGA230W is the optional cordless handset for the KX-TG2352W/KX-TG2382B. This installation manual only describes the steps necessary to start up the handset. Please read the KX-TG2352W/KX-TG2382B operating instructions for further details. 2.4GHz Expandable Cordless Handset Model No. KX-TGA230B/KX-TGA230W Charger Unit ...................................one Charger Order No. PQLV30017ZB (Black) Order No. PQLV30017ZW (White) AC Adaptor Order No. PQLV2Z (PQLV2) Handset Cover................................one Order No. PQKK10131Z3 (Black) Order No. PQKK10131Z2 (White) Battery ...............................one Order No. N4HHGMB00001 (HHR-P103) Belt Clip .............................one Order No. PQKE10352Z3 (Black) Order No. PQKE10352Z2 (White) Accessories (included) For extra orders, call 1-800-332-5368. Installing the battery Insert the battery into the handset as shown, matching the correct polarity (#). Press the battery down until it fits securely into the compartment ($). Close the cover. Installation! Connecting the AC adaptor •USE ONLY WITH Panasonic AC ADAPTOR PQLV2 (Order No. PQLV2Z). •The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.) 1 2 AC Adaptor Power Outlet (AC 120 V, 60 Hz) Char ging the y Place the handset about 15 hours before initial use. • The CHARGE indicator and “ Charging” will be displayed. • Recharge the battery when: – “ Recharge” is displayed, – “ ” flashes on the display, or – the handset beeps intermittently Charge Contacts • If the battery has been discharged, the display “ Charge for 15h” when you place the handset on the charger. The handset will not Keep charging until fully charged. CHARGE Handset battery information Indicator After your Panasonic battery is fully charged: Operation Operating time While in use (TALK) Up to 4 hours While not in use (Standby) Up to 7 days • Clean the charge contacts of the handset and the charger with a soft, once a month. Clean more often if the unit is subject to grease, dust or humidity. Otherwise the battery may not charge properly. Belt Clip! You can hang the handset on your belt or pocket using the belt clip. To attach the belt clip To remove the belt clip – 2 – Registration! This cordless base unit. The Only one handset Make sure the base Registration must be aCHARGE Indicator HANDSET LOCATOR (ALL) • The illustration of the base unit is the KX-TG2352W. The handset display shows the instructions as shown on the right. 1 1 Base unit: Press HANDSET LOCATOR (ALL) until the CHARGE indicator flashes. 2 2 Handset: # Press a. $ Wait until a long beep sounds and the display shows the registered number. The registration will be then complete. • The registered number “ [1] ” to “ [3] ” is shown on the top right of the display. • You can stop registration by pressing (OFF) on the handset and pressing HANDSET LOCATOR (ALL) on the base unit. Press [ALL] on base for 3 sec, then press [ H]. Handset Registering Ex. Extension number 3 Handset [3] Registered [3] • After you register the handset to the base unit, please confirm that the other (first one and second one) pre-registered handsets display “ Talk” by pressing . If one of the handsets does not display “ Talk” , re-register that handset to the base unit. To cancel the handset registration, please see the KX-TG2352W/KX-TG2382B Operating Instructions. For assistance, please call: 1-800-211-PANA(7262) – 3 – Optional Plugging a headset Please use only To order, call the Connecting the headset Open the headset jack cover, shown. H Headset Jack Wall Mounting! The charger can be wall mounted. Connect the AC adaptor. Install screws using the wall template below. Mount the charger ( # ). Slide it down ( $ ) then slide down to the right ( % ) until it is secured. $ # % Wall Template 2.45 cm ( 15. 16") Screws To Power Outlet 2.45 cm ( 15 . 16") – 4 – FCC WHEN PROGRAMMING TO EMERGENCY 1) Remain on the 2) Perform such activities This device complies with two conditions: (1) This device may not cause must accept any interference received, operation. Privacy of communications may not CAUTION: Any changes or modifications not expressly compliance could void the user’s authority to operate this device. Note: This equipment has been tested and found to comply device, pursuant to Part 15 of the FCC Rules. These limits reasonable protection against harmful interference in a residential equipment generates, uses, and can radiate radio frequency energy and used in accordance with the instructions, may cause harmful communications. However, there is no guarantee that interference particular installation. If this equipment does cause harmful interference television reception, which can be determined by turning the equipment off user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment in...