Outdoor Multi-Unit Telephone Interface (MUOTIU-EX) Test/Program Cord AC AdapterAntenna Assembly & Installation Step 1 Choose location near the de-mark location. Screw in antenna. Step 2 Mount to solid surface. Wiring to AC Adapter Connect the Solid Black Wire to the GND Terminal (shown below). Connect the Striped Wire to the +18V Terminal (shown below). PWR GND AC V Line INPOWER Line OUT Remove bottom panel of the MUOTIU-EX. Use the supplied Test/Program Cord for programming and testing before completing connections to phone company’s de-mark box. +18V GND RING TIP TIP RING LINE PHONE Power Active 1 Program Accessories With Existing Network Step 1: On the phone connected to the MUOTIU-EX, press “**07” after hearing the dial tone. Listen for double beep. Hang up and Learn LED will flash for 15 seconds. If an error tone is heard it means that memory will have to be cleared (see Troubleshooting). Step 2: Within 15 seconds enter Master PIN Number on MUGAPLM. A beep will be heard. Step 3: Press “05”. Step 4: Press “01” then press the Call button. The MUOTIU-EX will ring the telephone and Caller ID will display “Unit Learned”. NOTE: Ensure that all devices are not programmed. Step 1: On ONE Repeater, set Dipswitch #1 to ON. Step 2: Press Learn button on both Repeaters. Step 3: Enter Master PIN Number on the MUGAPLM followed by “05”. Step 4: Then press “01” followed by the Call button. The LEDs on the Repeaters will flash 3 times indicating programming is successful. Step 5: Wait until the MUGAPLM has stopped beeping or press the Cancel button before programming Repeaters to the MUOTIU-EX. Step 6: On the phone connected to the MUOTIU-EX, press “**07” after hearing the dial tone. Hang up and Learn LED will flash for 15 seconds. If an error tone is heard it means that memory will have to be cleared (see Troubleshooting). Step 7: Within 15 seconds press the Learn button on ONE Repeater. The LED will light. Step 8: The MUOTIU-EX will ring the telephone and Caller ID will display “Unit Learned”. NOTE: If the Repeaters have not been programmed to anything within an existing network, see Repeater manual for further instructions. NOTE: If programming into an existing network, ensure the MUOTIU-EX is programmed to the Active unit. The MUOTIU-EX acts as a wireless remote autodialer in a dedicated line system. A conversation cannot be held on the phone connected to the MUOTIU-EX. Features & Operation NOTE: Any features of the MUOTIU-EX do not require extra service from the Telephone Company. Answering Calls When visitor presses the number (00-63) then the Call button, the MUOTIU-EX will call the desired resident. If an expandable MUOTIU-EX system is used all phones within the system will ring. When call is answered from the MUOTIU-EX a repeating beep will be heard for up to 10 seconds. To accept the call dial “0”. To activate the primary gate operator dial “*9” on the phone connected to the MUOTIU-EX. Program Residential Phone Number Step 1: On the phone connected to the MUOTIU-EX, dial “*#”. A beep will be heard. Step 2: Enter a residence number 00 through 63. Step 3: Enter the telephone number of the desired residence (up to 14 digits). Step 4: Dial “#”. A beep will be heard. NOTE: For long distance calls, include proper prefix. Verify the Residential Phone Number Step 1: On the phone connected to the MUOTIU-EX, dial “**06#”. A beep will be heard. Step 2: Enter a residence number 00 through 63. Step 3: Dial “#”. A beep will be heard. Hang up the telephone. The telephone will ring and the call forwarding number that has been programmed will be displayed on Caller ID screen (briefly then disappears). Erase Phone Number To erase ONE phone number, on the phone connected to the MUOTIU-EX, dial “**03#(00-63)#”. To erase ALL phone numbers, on the phone connected to the MUOTIU-EX, dial “**01*****”. NOTE: Erasing all phone numbers can take up to 15 seconds. Repeaters Multi-Unit Gate Access Panel (MUGAPLM) Program Accessories With Existing Network Step 1: On the phone connected to the MUOTIU-EX, press “**07” after hearing the dial tone. Listen for double beep. Hang up and Learn LED will flash for 15 seconds. If an error tone is heard it means that memory will have to be cleared (see Troubleshooting). Step 2: Within 15 seconds enter Master PIN Number on MUGAPLM. A beep will be heard. Step 3: Press “05”. Step 4: Press “01” then press the Call button. The MUOTIU-EX will ring the telephone and Caller ID will display “Unit Learned”. NOTE: Ensure that all devices are not programmed. Step 1: On ONE Repeater, set Dipswitch #1 to ON. Step 2: Press Learn button on both Repeaters. Step 3: Enter Master PIN Number on the MUGAPLM followed by “05”. Step 4: Then press “01” followed by the Call button. The LEDs on the Repeaters will flash 3 times indicating programming is successful. Step 5: Wait until the MUGAPLM has stopped beeping or press the Cancel button before programming Repeaters to the MUOTIU-EX. Step 6: On the phone connected to the MUOTI...