valutazioni - 2, GPA: 3
(
)
)
|
Facilità d'uso
Turn the “PRIME/SPRAY” knob to the 16. “SPRAY” position and hold the Trigger down until all air and impurities are cleansed from the Hose and the paint runs pure. Release the Trigger. Turn the 17. “PRIME/SPRAY” knob to the “PRIME” position. Squeeze the Trigger once to make sure that pressure is released. Attach the Spray Tip: Turn the Sprayer off.18. Pull out and turn the key to lock the TriggerClose the gauge at the end of the tip to lock the gun 19. Lock the Gun and thread the Spray Tip on it. Painting: Fill a paint container (not included) 20. with paint. Follow paint manufacturer’s directions for the type of paint being used. Place the suction nozzle into the paint container. Turn the power switch of the Sprayer 21. to the “ON” position, turn the “PRIME/ SPRAY” knob to the “SPRAY” position, and turn the pressure switch to maximum. When the motor cycles off, unlock the 22. Gun and spray a test area. Adjust the pressure control dial until 23. a solid coat of paint of desired thickness is achieved. Painting Tips:24. Spray 10 to 12 inches from the • surface. Begin moving the Gun before • squeezing the Trigger. Release the Trigger before ending • the stroke. Paint using short, even strokes.• Keep the spray gun at a right angle • to the painting surface. Keep the tip of the spray gun paral• lel to the ground. Overlap each stroke by about 30% • to ensure an even coat. When finished, turn the Power Switch 25. to its “OFF” position. Point the Gun into the waste container and squeeze the Trigger to discharge Gun and Hose pressure. Lock the Gun. Disconnect the power supply after 26. use. Clean, then store the tool indoors out of children’s reach. Maintenance And Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. To prevent serious injury from accidental operation: Turn the Power Switch of the tool to its “OFF” position and unplug the tool from its electrical outlet before performing any inspection or maintenance. To prevent serious injury from tool failure: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication BEFORE EACH USE,1. inspect the general condition of the tool. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. After Use,2. When using latex paint, clean the sprayer and components with clean water. When using oil based paint, use mineral spirits to clean the sprayer and components. Lock the Gun and remove the Spray a. Tip assembly. Submerge the Suction Tube in a b. container with the appropriate cleaning solution. Place the waste material container c. next to the paint container. Aim the Spray Gun into the paint d. container and pull the trigger. Turn the Power switch to the “ON” e. position and the “PRIME/SPRAY” knob to “SPRAY”. Purge the paint into the original container until the cleaning solution starts coming out. Move the Spray Gun to the waste f. container and continue holding the Trigger down until the cleaning fluid coming out is paint-free. Release the Trigger, turn the g. “PRIME/SPRAY” knob to “PRIME” and pull the trigger once to release pressure. Turn the power switch of the unit h. “OFF” and lock the Gun. Remove the Suction Hose and rei. turn tube and clean them. Wipe the thread of the inlet nut and j. remove and clean the inlet filter. Thread the suction tube back in k. place and reconnect the return tube onto the return tube fitting. Submerge the suction set in a conl. tainer of NEW cleaning solution. Turn the “PRIME/SPRAY” knob to m. “PRIME” and squeeze the trigger once into the waste container to relieve pressure. Allow the pump to circulate the n. cleaning solution through the suction set for three minutes. If oil based paints were used, the unit must be flushed with water after being flushed with mineral spirits. Turn the power switch Off and uno. plug the Sprayer. Remove the Gun from the hose. p. Remove the filter from the spray q. gun. Clean with a soft brush and appropriate cleaning solution. Remove the spray tip from the gun r. and clean with a soft brush and the appropriate cleaning solution. Clean the washer, and spray tip s. seat. Reassemble the Gun.t. 3. WARNING! If the supply cord of this power tool is damaged, it must be replaced only by a qualified service technician. Troubleshooting Problem Possible Causes Likely Solutions Sprayer will not start No power at outlet.1. Cord not connected.2. Sprayer turned off under 3. pressure. Check power at outlet.1. Check that cord is plugged in.2. Turn pressure control knob to maximum, or 3. PRIME/SPRAY knob to PRIME. Sprayer will not draw paint Sprayer has lost prime.1. Paint level too low in container.2. Suction set clogged.3. Suction tube loose at inlet.4. Prime sprayer again.1. Fill paint container.2. Clean suction Set.3. Tighten Suction tube connectio...