valutazioni - 1, GPA: 5
(
)
)
|
Facilità d'uso
2) When you get to the end of the line, release the Trigger for a moment and then apply the product in the opposite direction just beneath the line you have sprayed. 3) Next, to achieve a vertical strip adjust the Spray Direction Plate (4) to the horizontal position then pull the Trigger and move your arm up and down over the horizontal strips you just have sprayed. Through gradual movement of the Spray Direction Plate (4) between Horizontal, Vertical and Round spray pattern you can vary the width of the pattern (Fig.6) HINT: To obtain the best results always keep your Spray Gun level and at an equal distance from the object you are spraying, ideally 25-30cm (10“-12”) (Fig.8/9). Let your arm control the movement rather than your wrist (Fig.8/9). This will help give you an even paint distribution. Fig.7 Fig.7 CAUSE ACTION REQUIRED Paint too diluted Add undiluted paint Paint output too high Reduce the paint output by adjusting the Paint Flow Adjuster (9) Moving too slowly Increase speed of application Spray Trigger held for too long Release Trigger sooner Spray Gun too close Increase the distance between the Spray Gun and the work surface Paint too diluted Add undiluted paint Paint output too low Increase the paint output by adjusting the Paint Flow Adjuster (9) Moving too fast Reduce speed of application Spray Gun clogged Clean the Spray Gun Spray Gun too far away Move the Spray Gun closer to the work surface Paint too thick Add thinner Fluid Tip clogged Clean the Fluid Tip (5) Pick-up Tube clogged Clean Pick-up Tube (11) Air Hose split Replace air Hose (13) Grainy paint Filter the paint Paint Container almost empty Refill Paint Container (12) Spray Gun at an angle Check that the Pick-up Tube (11) is pointing towards the paint Air inlet blocked Check the condition of the Filter (14) and clean if necessary You move your wrist Move your forearm instead Either too much or not enough paint Use the Paint Flow Adjuster (9) to control the flow PROBLEMThepaintdripsontoitembeingpaintedPaintistoothinorirregularNopaintbeingreleasedToomuchpaintinanareaApplicationTROUBLESHOOTING SPRAY GUN PROBLEMThepaintdripsontoitembeingpaintedPaintistoothinorirregularNopaintbeingreleasedToomuchpaintinanareaApplicationTROUBLESHOOTING SPRAY GUN 6 PLEASE NOTE: We have done all we can to ensure that when used correctly and in accordance with these instructions the spray gun has a long and fault-free life. We accept no responsibility for damage caused by the use of incorrect or unsuitable substances, paints or liquids which have not been thinned correctly or which are not suitable for the surfaces to which they are applied, health hazards arising from a lack of ventilation when working in confined spaces or equipment which is faulty due to inadequate cleaning of the components after use. If in doubt, test a small inconspicuous area first. Always read the manufacturer s instructions before use. Neither our guarantee nor the above statement affects your statutory rights. MAINS CONNECTION This unit is a Class II appliance which means it is double insulated for your protection, no earthing wire is necessary. If the supply cord is damaged, it must be replaced by Earlex Ltd or our appointed agents. If you are using an extension lead it must be rated at a minimum of 6 amps and fully unwound. Do not operate with a lead rated at less the 6 amps as this will cause premature failure of the motor which is not covered by the guarantee. If the plug is cut off from the mains lead, it must be disposed of safely. NEVER under any circumstances insert a plug which is cut off from the mains lead into socket. Information on the disposal of waste electrical ! electronic equipment is known as WEEE. Please do not dispose of tools with your household waste collected by the council. It is your responsibility to dispose of this type of waste by handing it over to a special designated collection point for recovery and recycling. EC Declaration of Conformity We declare that the unit: HV2900, 3500 and 3900 Conforms to LVD 2006/95/EC, EN60335-1, EMC 2004/108/EC, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3, EMF EN50366, EN 62233 Tim Hopper Technical Director All rights reserved © 2011 Design Registrations and Patents: Spray Gun Design Registration ECD 001096218-0001 CN 200930004457.X US D609, 778S Spray Gun Patent GB 0903275.6 HV2900/HV3900 Turbine Design Registration GB 3022947 EU 000608856 US D563,503 HV3500 Turbine Design Registration ECD 001096242-0001 CN 200930004458.4 US 29/314,080 EARLEX LTD. WILL ACCEPT NO RESPONSIBILITY FOR THE USE OF THIS PRODUCT IF USED FOR ANY OTHER PURPOSES THAN THOSE DETAILED HEREIN. GUARANTEE and HELPLINE This product is guaranteed for a period of 24 months against faulty manufacture or materials. It is not guaranteed for industrial or hire purposes. This guarantee does not affect your statutory rights. For further information or any user advice, please phone our helpline between 08:30 to 17.00 Mondays to Thursday, Friday 08:30 to 15:45 ...
Questo manuale è adatto anche per i modelli :Pistole - HV3500 (2.78 mb)
Pistole - HV2900 (2.78 mb)