valutazioni - 4, GPA: 3.8
(
)
)
|
Facilità d'uso
Cleaning Pump Turn Pressure to HIGH (completely clockwise) 3 4 Lift Suction Assembly above Paint Level in Bucket Turn Prime/Spray Control to PRIME Position 1 6 Wipe Exterior of Suction Assembly and Bypass Tube Suction Assembly and Bypass Tube in Bucket of cleaning fluid 2 Turn power switch to ON (shown in the OFF position) 5 Airless Paint Sprayers Operating Instructions and Assembly Instructions Cleaning Hose and Gun Turn Prime/ Spray Control to SPRAY (knob is vertical) If Reversible Tip is Used, Rotate Spray Tip to CLEAN Position. While Pulling Trigger, Direct Fluid Stream Along Inside of Bucket 9 10 Cleanup fo r Changing Paints or Tempo rary Sto rage fo r Mo re Than One Nig ht (Continued) Allow the cleaning fluid to continue circulating for approximately 10 minutes. 7. Turn pressure to HIGH (completely clockwise). 8. Turn prime/spray control to SPRAY/ ROLL position. 9. If reversible tip is used, rotate spray tip to CLEAN position. 10. Point spray gun into bucket of paint and pull trigger. NOTE: To reduce splashing, direct fluid stream along inside of bucket and above the paint level. 11. As soon as cleaning fluid is flowing from spray gun, release trigger. NOTE: It should take less than one minute to clear each 25 feet of high pressure hose. 12. Engage gun trigger lock. 13. Turn prime/spray control to PRIME position. 14. Turn pressure control to HIGH. 15. Lift suction assembly above fluid level in bucket. NOTE: Allow pump to run until empty. 16. Repeat process (1 - 15) with fresh cleaning fluid, to remove contaminated cleaning fluid from initial cleaning. Turn Pressure to HIGH (completely clockwise). 7 8 Engage Gun Trigger Lock 12 Prime Position Lift Suction Assembly High Pressure Position (completely clockwise) 12 Paint To Lock Locked 13 14 15 13 Operating Instructions and Assembly Instructions Airless Paint Sprayers Cleanup fo r Changing Paints or Finishing Touches/Shutdown Tempo rary Sto rage fo r Mo re Than One Nig ht (Continued) 17. Make sure prime/spray control is in SPRAY position to reduce dribbling. 18. Turn pressure to LOW (completely counterclockwise). 19. Turn power switch to OFF position. 20. With gun pointed in safe direction pull trigger with lock released to relieve any pressure in hose. 21. Engage gun trigger lock. 22. Clean buckets and dispose of any waste paint and cleaning fluid in an environmentally responsible manner. 23. Clean tip guard with cleaning brush and cleaning fluid. NOTE: At this point, pump, hose and spray gun are clean, but still require further preparation for storage of more than one day. 17 Prime/Spray is in SPRAY/ROLL Position 18 Turn Pressure to LOW (completely counterclockwise) Pull Gun Trigger with Trigger Lock Released Engage Gun Trigger Lock 21 20 To Lock Locked Airless Paint Sprayers Operating Instructions and Assembly Instructions Storage short te rm (less than one wee k) WEAR ALL NECESSARY SAFETY GEAR Necessa ry Too ls / Mate ria ls: • Pump Protector Solution • Plastic Wrap • 3/4 in. or Adjustable Wrench Oil or Alkyd Based Paint If sprayer cleaned with mineral spirits, simply wrap suction filter housing in plastic to keep debris out of suction filter. No other preparation is necessary. Water -based paint 1. Prepare Pump Protector solution in bucket as directed on container. 2. Place suction assembly into solution. 3. Place end of bypass tube into waste bucket. 4. With prime/spray control in PRIME position, turn pressure to HIGH (completely clockwise). 5. Turn power switch ON. Circulate Pump Protector through bypass tube until bucket of solution is EMPTY. 6. Turn pressure to LOW (completely counterclockwise). 7. Wrap suction filter housing in plastic to keep debris out of suction filter. long te rm (more than one weeK ) 8. Remove high pressure hose and drain. Reassemble high pressure hose to pump. 9. With spray tip attached to spray gun, wrap tip with plastic to protect tip. Water Based Paint Pump Protector Prepare Pump Protector Solution 1 Turn Pressure to LOW (completely counterclockwise) P L A S T I C W R A P Wrap Suction Filter Housing in Plastic Place Suction Assembly in Solution PUMP PROTECTION SOLUTION WASTE BUCKET 6 7 Place End of Bypass Tube into Waste Bucket With Prime/Spray Control in PRIME Position, Turn Pressure to HIGH (completely clockwise) 14 2 PUMP PROTECTION SOLUTION WASTE BUCKET PUMP PROTECTION SOLUTION WASTE BUCKET 3 4 Operating Instructions and Assembly Instructions Airless Paint Sprayers Spray Gun maintenance pump damage may occur if these instructions are not followed. Before performing any maintenance, make sure to relieve pressure from system and disconnect power from sprayer. • Do not use oil based solvents to clean equipment after using latex based coatings. Use only warm soapy water. • Always replace clogged gun filters, do not attempt to clean them. • Carefully follow cleaning and storage instructions for your sprayer. • Do not use metal or other hard objects to pick d...
Questo manuale è adatto anche per i modelli :Pistole - PS231B (7.95 mb)
Pistole - PS240C (7.95 mb)
Pistole - PS240F (7.95 mb)
Pistole - PS250E (7.95 mb)