valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
(See notes in Maintenance Section on oil leaks.) Turn Pressure Control to Low Pressure/Hydraulic Bleeding position for 1 minute Motor runs, but pump does not prime even though it was working just fine a little while ago. (Usually occurs after moving or adding more paint to the paint bucket.) 14 See Possible Causes 9,10,11,13 14.See Corrective Actions 9,10,11,13 15.Clogged suction filter 15.Remove suction filter and clean. Also, refer to Maintenance section 16.Trash caught in valves 16.See “Force Feeding” figure on page 23 17.Paint sediments settled to bottom of bucket 17.Strain and mix paint thoroughly Pump primes, but does not build pressure 18.Prime/Spray Control not in Spray position 18.Turn Prime/Spray Control to Spray position 19.Pressure Control not set to high enough pressure 19.Turn Pressure Control clockwise to desired pressure. Fully clockwise is maximum pressure 20.Even though Prime/Spray Control is in Spray position, fluid still flows from By-Pass Tube. Prime/Spray Control is worn or damaged 20.Replace with service kit (See replacement parts list) or take equipment to authorized service center Continued on next page Troubleshooting Chart Operating Instructions and Assembly Instructions 21 Symptom Possible Cause(s) Corrective Action Motor hums and does not run 1. Unit under pressure 1. Turn Prime/Spray Control to prime position 2. Equipment has been dropped which caused motor to become misaligned 2. Take to authorized service center to have motor assembly realigned. Or, call technical support 3. Supply voltage too low 3. Do not use an extension cord, it is better to add hose length. Use portable generator with a 2400 VA minimum rating Motor does not run or hum 4. Power Switch is in OFF position 4. Flip Power Switch to ON position 5. Bad power connection 5. Check power connections at power receptacle, along extension cord and at equipment for looseness or damage 6. Circuit breaker or fuse is tripped 6. correct cause of circuit overload. (Possible causes: Supply voltage too low, extension cord too long for available supply voltage, equipment was under pressure while trying to start motor or motor has been damaged.) 7. Thermal overload protection activated 7. Allow motor to cool for approximately 30 minutes, determine cause and restart motor. (Possible causes: Supply voltage too low, extension cord too long for available supply voltage, equipment was under pressure while trying to start motor or motor has been damaged.) Motor runs, but pump does not prime after being cleaned after last use. (This problem can usually be prevented by following the recommended cleaning and storage procedure) 8. Check valves stuck 8. “Pop” Inlet Valve and Outlet Valves. See Preparation Instructions 9. Suction Assembly loose and/or sealing surfaces are dirty at Inlet Valve 9. Remove Suction Assembly, clean sealing surfaces and reassemble 10.Suction Head not immersed in paint 10.Add more paint to bucket and/or adjust position of Suction Assembly 11.Prime/Spray Control is in the spray position and/or the Pressure Control is in the Low Pressure/Hydraulic Bleeding position 11.Turn the Prime/Spray Control to the Prime position and Pressure Control fully clockwise 12.Hydraulic system contains air 12.Turn Pressure Control to Low Pressure/Hydraulic Bleeding position for 1 minute while motor is running 13.Hydraulic oil level low 13.Add oil so level is within 1/4” of housing edge. (See notes in Maintenance Section on oil leaks.) Turn Pressure Control to Low Pressure/Hydraulic Bleeding position for 1 minute Motor runs, but pump does not prime even though it was working just fine a little while ago. (Usually occurs after moving or adding more paint to the paint bucket.) 14 See Possible Causes 9,10,11,13 14.See Corrective Actions 9,10,11,13 15.Clogged suction filter 15.Remove suction filter and clean. Also, refer to Maintenance section 16.Trash caught in valves 16.See “Force Feeding” figure on page 23 17.Paint sediments settled to bottom of bucket 17.Strain and mix paint thoroughly Pump primes, but does not build pressure 18.Prime/Spray Control not in Spray position 18.Turn Prime/Spray Control to Spray position 19.Pressure Control not set to high enough pressure 19.Turn Pressure Control clockwise to desired pressure. Fully clockwise is maximum pressure 20.Even though Prime/Spray Control is in Spray position, fluid still flows from By-Pass Tube. Prime/Spray Control is worn or damaged 20.Replace with service kit (See replacement parts list) or take equipment to authorized service center Continued on next page Operating Instructions and Assembly Instructions Troubleshooting Chart (Continued) Symptom Possible Cause(s) Corrective Action Pump primes and builds pressure, however, the equipment does not spray or produce a quality spray pattern 21.Clogged gun filter 22 Clogged Spray Tip 21.Replace with new filter. Do not attempt to clean gun filters. Also, refer to Maintenance section 22.See Clearing Clogs section 23 A. Tip is...
Questo manuale è adatto anche per i modelli :Pistole - PS290D (6.56 mb)
Pistole - PS270D (6.56 mb)
Pistole - PS271D (6.56 mb)