Log:
Scaricare : 0   File Size : 167 kb   Produttore : Harbor Freight Tools  
Categoria : Pistole
@name

19. WARNING! The warnings and cautions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be under- stood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. OPERATING INSTRUCTIONS To Fill The Container (31): 1. CAUTION! Always wear eye, breathing, and skin protection. Wear ANSI approved safety impact goggles, an ANSI approved respirator, latex gloves, and proper

Scaricare : 0   File Size : 167 kb   Produttore : Harbor Freight Tools  
Categoria : Pistole
@name

8. Store idle tools and equipment out of reach of children and other untrained people. Tools and equipment are dangerous in the hands of untrained users. 9. Maintain the Sprayer with care. Keep this product clean. A properly maintained tool is easier to control. Do not use damaged tools and equipment. Tag damaged tools and equipment “Do not use” until repaired. 10. Check for misalignment or binding of moving parts, loose or broken parts, and any other condition that may affect the Sprayer’s oper

Scaricare : 3   File Size : 1 mb   Produttore : Harbor Freight Tools  
Categoria : Pistole
@name

An in-line shutoff ball valve is an important safety device because it controls the air supply even if the air hose is ruptured. The shutoff valve should be a ball valve because it can be closed quickly. Note: Do not use an automatic oiler system or add oil to airline. The oil will contaminate the material being propelled, ruining the final result. 2. Attach an air hose to the compressor’s air outlet. Connect the air hose to the air inlet of the tool. Other components, such as a coupler plug and

Scaricare : 1   File Size : 2 mb   Produttore : Harbor Freight Tools  
Categoria : Pistole
@name

Follow the manufacturer’s directions. Most paints will spray easily if they are thinned properly. 2. Thin the paint according to manufacturer’s directions and mix thoroughly. 3. Carefully strain the paint through a paint strainer or a piece of cheesecloth. 4. Fill the Cup to 3/4 full. Close Cup. 5. Start the air compressor and set the regulator to needed pressure. Do not exceed maximum air pressure. 6. Test the consistency by spraying on a piece of scrap material. If it still appears too thick,

Scaricare : 0   File Size : 615 kb   Produttore : Harbor Freight Tools  
Categoria : Pistole
@name

Connect the Red Air Hose (41) to the Air Outlet Connector (36). Attach the other end of the Red Air Hose (41) to the Air Inlet (80) on the Gun. 2. Set the air pressure on your compressor to 30-43 PSI. Do not exceed the maximum air pressure of 43 PSI. Also, set the air pressure on the Air Regulator to 10-30 PSI, as shown on the Gauge (38). 3. Check the air connection for leaks and then disconnect the tool from the air source. Control Layout FIGURE 1 Pattern Control Knob (57) Trigger (78) Air Cap

Scaricare : 4   File Size : 361 kb   Produttore : Harbor Freight Tools  
Categoria : Pistole
@name

risk of Fire or explosion from Materials incompatible with aluminum. Certain solvents, including 1,1,1-Trichloroethane and Methylene Chloride can chemically react with the Aluminum used in this spray equipment. This can cause an explosion which may result in death or serious personal or property injury. Other chemicals ,when mixed, may cause unpredictable results. Inform yourself by reading the information provided with each solvent before introducing to the sprayer. Never spray the solvents nam

Scaricare : 9   File Size : 616 kb   Produttore : Harbor Freight Tools  
Categoria : Pistole
@name

If any parts are missing or broken, please call Harbor Freight Tools at 1-800-444-3353 as soon as possible. Charging Instructions The Battery (51) for the Sprayer must 1. be fully charged before using the tool. When charging for the first time, and all subsequent charges, the charge time is 8 hours. Never charge the Battery (51) for longer than 8 hours, as damage to the Battery and/or Sprayer will occur. CHARGER(63) CHARGINGPLUGPOWER SWITCH(58) FIGURE ECHARGE FOR 8 HOURS(DO NOT OVERCHARGE) 2. To

Scaricare : 0   File Size : 2 mb   Produttore : Harbor Freight Tools  
Categoria : Pistole
@name

Addresses practices not related to personal injury. IMPORTANT SAFETY INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. WARNING – When using tools, basic precautions should alwa

Scaricare : 4   File Size : 1023 kb   Produttore : Harbor Freight Tools  
Categoria : Pistole
@name

Keep the distance from the object being painted at 6” to 9”. This may slightly differ depending on the flow adjustment and the material being sprayed. Do not stop the gun movement while spraying. If you stop the gun for even just a slight pause while spraying, the paint will build up and run down the workpiece. FIGURE 5 (Heavier coat on one side, uneven coverage) Incorrect (Even coverage) Correct (90o) 2. To ensure you don’t allow paint to build up, start moving the Spray Gun before you Squeeze

Scaricare : 4   File Size : 759 kb   Produttore : Harbor Freight Tools  
Categoria : Pistole
@name

After the adjustment, tighten the Lock Ring by hand. See FIGURE 3 below. Pattern Adjustment Warning!! Never exceed the Maximum Inlet PSI of 70 PSI. 1. If you need to reduce the air pressure for specific areas, adjust the air compressor. 2. To set the pattern size specific to the job, use the Pattern Control Knob (16) (see FIGURE 1 on page 6). By turning it counterclockwise (all the way open), the pattern will flatten. Turn the Pattern Control Knob (16) clockwise for a round pattern. See FIG





categorie