valutazioni - 3, GPA: 4 ( )

Produttore : Oregon Scientific File Size : 2.12 mb File Nome : Lingua di insegnamento:

Together we can improve the world we live in. Over view Front View 1 10 11 12 13 14 15 16 2 3 4 5678 9 1. : Remote sensor reception indicator and outdoor channel selected 2. Outdoor temperature 3. Indoor temperature 4. Weather forecast 5. : Clock signal reception indicator 6. : Alarm time is displayed 7. : Daily alarm is On 8. AM / PM 9. Rechargeable battery status LED indicator 10. : Outdoor remote sensor battery low 11 . : Main unit back-up batteries low / no battery 12. : AC adaptor connected 13. : Rechargeable battery is low / solar panel detached 14. : Rechargeable battery level indicator 15. : Time zone offset 16. Calendar / Clock with weekday / seconds Top View 1 2 3 4 5 6 1. SNOOZE: Activate snooze alarm / backlight 2. / : Increase / decrease value of the setting; activate / deactivate clock reception signal 3. : Change display; set clock 4. : Toggle between outdoor temperature channels (1-3); initiate auto-toggle 5. : View alarm status; set alarm 6. : Activate / deactivate alarm function botom View 1 2 3 1. SEARCH: Initiate sensor search 2. RESET: Reset unit to default settings 3. °C / °F: Select temperature unit SOLAR PANEL 1 2 3 4 5 1. CHARGING: charging in process 2. FULL: batteries fully charged (when TEST is pressed) 3. Solar panel 4. TEST establish if battery is full 5. Battery compartment REMOTE SENSOR 1 2 3 4 5 1. LED status indicator 2. Wall mount hole 3. Battery compartment 4. RESET: Reset unit to default settings 5. CHANNEL switch GETTING STARTED Solar Pane l This product uses two AAA rechargeable batteries which should be charged via the solar panel. For the batteries’ first charge, it is strongly advised to charge it for at least 12 hours. To charge the battery: 1. Detach solar panel by exerting downward pressure and pulling at a 45° angle (approx.) away from main unit. 2. Insert 2 AAA rechargeable batteries in battery compartment located at the back of the solar panel. IMPORTANT Place ONLY NiMH type rechargeable batteries in the solar panel battery compartment. Do not charge non-rechargeable batteries. 3. Expose the solar panel directly to sunlight for approximately 5-6 hours to charge the battery. The (red) CHARGING LED on solar panel will light up indicating there is sunlight and unit is charging. TIP Press and hold TEST located at the back of the solar panel. (Green) FULL LED indicates batteries have been fully charged. 4. Align holes with protruding plastic. Push solar panel towards main unit and snap into place. 5-6 hours of battery charging will normally provide power to operate unit for 2 months. When the rechargeable battery is nearly flat or when solar panel has been detached, the (green) LED indicator on the main unit and will flash. TIPS • For best results when charging the battery, place the solar panel directly with view to sunlight. • Direct solar panel as follows: Solar panel facing: if you reside in the: North Southern Hemisphere South Northern Hemisphere • Do not scratch the solar panel’s surface or wipe it with strong detergent. • Do not expose the solar panel to rain, snow or moisture. • The duration of the rechargeable battery’s charging or operating time is determined by either the intensity of sunlight or the position of the solar panel towards the sun. • Do not overcharge the batteries. Bac kup power 1 piece AAA battery In the case when the rechargeable battery is flat or nearly flat or when the solar panel has been detached, the AAA battery can act as backup power supply for the main unit. 1. Remove the battery compartment located at the base of the unit. 2. Insert the battery, matching the polarity. 3. Press RESET after each battery change. Power adaptor (not included) The adaptor powers the unit and can also be used for charging the rechargeable battery. When connected to the main unit, will be displayed. NOTE The main unit and adaptor should not be exposed to wet conditions. No objects filled with liquid, such as vases, should be placed on the main unit and adaptor. Remote sensor This product can work with up to 3 sensors at any one time to capture temperature readings in various locations. To set up the remote sensor: 1. Slide open the battery compartment. 2. Slide channel switch to select a channel (1, 2, 3). Ensure you use a different channel for each sensor. 3. Insert the battery, matching the polarities. 4. Press RESET after each battery change. 5. Close the battery compartment. 6. Press and hold SEARCH for 2 seconds to initiate a sensor search. NOTE Use alkaline batteries for longer usage and consumer grade lithium batteries in temperatures below freezing. The remote sensor reception icon will show the following status: ICONS MEANING Main unit is searching for sensor(s) A sensor channel has been found No sensor found TIP Ideal placements for the sensor would be in any location on the exterior of the home at a height of not more than 1.5 m (5 ft) and which can shield it from direct sunlight or wet conditions for an accurate reading. 1.5 m (5 ft) cloc k ...

Scarica la tua

Per scaricare, digitare 2 cifre :