valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
SET TIME SET RESETOFF WEATHERBUZZERSOUNDSDM SNOOZE/DIMMER ALARMSETNOAAON/SLEEP SOUND M ONTH FWD DA TE REV W I N DB R O O KF O R E S TO C E AN DAIL Y ALARM7-5-2 WEATHER ON/SLEEP SUN POWER DST LOWLOW Model T150 Weather On/Sleep button Sounds Button Weather Button Snooze/Dimmer Bar Alarm Set Button Buzzer Button Sound On/Sleep Button DC Jack Off/Reset Button Time Set Button 7•5•2 Button Calendar Set Button FWD Button Sleep Volume Button REV Button Volume Control Weather Band Ocean Button Wind Button Forest Button Brook Button Preparation for Use Preparation for Use 1. Remove the radio and all packing materials from the carton. You should save all the packing materials if the unit ever needs to be returned for service. If you do not wish to save the materials, please dispose of them properly. 2. Place the unit on a stable, level surface, close to an AC outlet, out of direct sunlight, and away from sources of excess dust, dirt, heat, water, moisture, vibration and strong magnetic fields. DC Operation • This unit can operate on both AC and DC power. An AC adapter was included with this unit. For further instructions on operating this unit using AC power, see AC Operation. •3 “AA” alkaline batteries can operate the unit without AC power. They will also continue running the unit if it is operating on AC power and there is a power failure. For best results, you should always have fresh “AA” alkaline batteries installed in this unit. • This unit comes with a CR-2032 lithium battery already installed. The CR-2032 is to maintain the time and alarm settings. 3 “AA” Main Battery Installation 1. Gently turn the unit over and remove the battery compartment door. 2. Install 3 “AA” alkaline batteries, while making sure that the + and – ends match up with those inside the battery compartment. 3. Close the battery compartment door and turn the unit right side up. Note: This unit was designed to operate on alkaline batteries only. You must use alkaline batteries with this unit. When the batteries are getting weak the Battery Low Icon ( LOW ) will flash on the right side of the display. Lithium Battery Backup Installation 1. Gently turn the unit over and open the battery compartment door. If necessary, remove the 3 “AA” batteries to get to the lithium battery door. 2. Loosen the screw and remove the lithium battery door. 3. Replace the CR-2032 lithium battery, while making sure that the + and – ends match up with the markings inside the battery compartment. 4. Place the door back on and tighten the screw, then reinstall the 3 “AA” batteries and close the battery compartment door. Note: This unit comes equipped with a CR-2032 lithium battery used for battery backup purposes only. When the lithium battery is getting weak the Lithium Battery Low Icon ( LOW ) will flash on the left side of the display. Battery Backup System If the unit is being operated through AC power and there is a power interruption, the 3 “AA” batteries will takeover and run the unit. All settings, alarms, and instant weather will operate. If the unit is operating through DC power (3 “AA” batteries) and there is a power interruption, then the lithium battery (CR-2032) will maintain the time and alarm time settings and operate the sure alarm. The sure alarm will default all alarms to buzzer and turn on for 2 minutes. All settings will be lost if there is a power failure and no batteries are installed. AC Adapter Operation • Plug the supplied AC adapter into the DC Jack on the back of the unit, then plug the cord into an outlet. • If you are using a different AC adapter then the one supplied, make sure that it is a 6V, 300mA Positive Center AC adapter. Setting the Clock Time and Calendar Important •While setting the time or calendar, if you do not press the appropriate buttons (as explained below) within approximately 8 seconds the display will stop flashing. If this happens you must follow the steps again from step 1. • While setting the time, if you press and hold the FWD or REV button the minutes will begin at a moderate pace, then get faster. This will assist you in setting the time both fast and exact. Setting the Clock Time 1. Press and hold the Time Set button until the display begins flashing. 2. Press the FWD or REV button to set the correct time. REMEMBER to set the correct AM or PM. The PM Indicator is located on the upper left side of the display. 3. Press the Time Set button to return to normal mode. A beep will confirm that the time is set. Setting the Calendar 1. Press and hold the Calendar Set button until the display begins flashing. 2. Press the FWD (Month) button to set the correct month. 3. Press the REV (Date) button to set the correct day. 4. Press the Calendar Set button to return to normal mode. A beep will confirm that the calendar is set. Listening to Instant Weather Fully extend the wire antenna and vary the direction for the strongest signal. Important – If the Weather On/Sleep button is pressed more than o...