valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
CUSRheinland Production inspected 1820 19 17 16 15 OUT OUT IN Channel Two BALANCEDUNBALANCED OUT OUTIN Channel One BALANCEDUNBALANCED OUT INOUT INGND LIFT RISK OF FIRE-REPLACE FUSE AS MARKED TUVRheinland ofNorthAmerica, Inc. CUSRheinland Production inspected IN IN SERIALMODEL20 18 17 16 1517 16 15 GND LIFT OUT IN UNBALANCED OUT IN BALANCED OUT IN RISK OF FIRE-REPLACE FUSE AS MARKED SERIALMODELTUVRheinland ofNorthAmerica, Inc. CUSRheinland Production inspected 1820 19 17 16 15 PUSH 2 1 3 NEW TIDE EQU131VU Rear Panel PUSH 2 1 3 NEW TIDE PUSH 2 1 3 NEW TIDE PUSH 2 1 3 NEW TIDE PUSH 2 1 3 NEW TIDE EQU231TWIN Rear Panel 19 GND LIFT RISK OF FIRE-REPLACE FUSE AS MARKED SERIALMODELOUT IN UNBALANCED OUT IN BALANCED ChannelTwoOUT IN UNBALANCED BALANCED Channel One INOUT INOUTOUT IN 20 17 16 1518 PUSH 2 1 3 NEW TIDE PUSH 2 1 3 NEW TIDE Channel Two 15. XLR input and output connector The XLR connector are actively balanced and are used to input/output the signal. 16. 1/4" TRS phone plug input and output connector The 1/4" TRS connector are actively balanced and are used to input/output the signal. 7 17. RCA input and output connector The RCA connector are unbalanced. NOTE: While you can use any input connector with any output connector, only one set of these connectors is to be used at one time, detail wiring and connection, please refer to 4.2 audio connection. 18. Ground lift switch This switch is used to disconnect the signal ground from the mains and chassis earth. If it is determined that the equalizer is the cause of hum or buzz in your system due to a ground loop, move this switch to the "lift" position. 19. Fuse holder / Voltage selector You must be sure of the Voltage available in your country because this is a Dual Voltage unit. Voltage operation can be changed through the fuse protecting the power supply but this operation must be performed by a qualified engineer. 110-120V 220-240V 220-240V 110-120V THIS IS SET FOR THIS IS SET FOR 110V AC TO 120V 220V AC TO 240V AC OPERATION AC OPERATION Please note the triangular markers on both sides of the fuse holder (see above figure). To change the voltage pull the fuse holder out, rotate it 180 and push it back again. The operating voltage will be indicated by one of the two triangular markers. 20. AC Inlet This connector is meant for the connection of the supplied main cord. Do not insert power cord into unit until voltage has been correctly set. Do not plug power cord into AC power until voltage has been correctly set. 4. INSTALLATION & CONNECTION 4.1 Mains Connection Please ensure that the EQU Series Graphic Equalizer is set to the correct supply voltage before plugging the power cord into the wall outlet, use the same fuse as marked on the fuse holder at the AC power connection socket. The mains connection of the EQU Series Graphic Equalizer is made by using the enclosed mains cord and a standard IEC receptacle. It meets all of the international safety certification requirements. 4.2 Audio Connection The EQU Series Graphic Equalizer presents with balanced XLR & 1/4" TRS and unbalanced RCA connectors, and it can be interfaced by several ways to support a variety of applications without any signal loss. The EQU Series Graphic Equalizer can be used on a single instrument by connecting to a mixing console's main inserts, or on an entire mix "in-line" between a mixing console's outputs and a power amplifier. -Wiring Configuration Either the 1/4" TRS phone jack or the XLR connector can be wired in balanced and unbalanced modes, which will be determined by the actual application status, please wire your system as the following wiring examples: Pin3 (-) Pin2 (+) Pin1 ( ) (Linked to Pin1 manually, ) Pin1 ( ) Pin2 (+) Pin3 (-) Tip Ring Sleeve + - Tip Ring Sleeve + Sleeve Tip + TS Type Unbalanced TRS Type Balanced TRS Type Unbalanced XLR Type Unbalanced XLR Type Balanced 8 9 - Insert Points Connection 4.3 Rack Mounting - In Line Connection For these applications the EQU Series Graphic Equalizer provides 1/4" TRS connectors, XLR connectors and RCA connectors to easily interface with most any professional audio device. Follow the configuration examples below for your particular connection. Send Return Ring Tip Sleeve 1/4" TRS insert Insert Leads 21 3 1 2 3 TIP RING SLEEVE TIP RING SLEEVE SLEEVE TIP SLEEVE RING TIP TIP RING SLEEVE Centre (Send) Screen Centre (Return) Screen Tip Ring Sleeve Tip (Send) Sleeve Sleeve Tip Ring Sleeve 1 2 (Send) 3 1 2 (Return) 3 Tip Ring Sleeve Tip (Return) If you are connecting to a mixing console's main inserts, you may have a single TRS jack for SEND & RETURN, in this case, use an insert "Y" cable that configured like the examples below. The most secure mounting is on a universal rack shelf available from various rack manufactures or your music dealer. The EQU Series fits into one standard 19" rack unit of space, but the EQU131 and EQU215 will be 1H height, the EQU231TWIN will be 4H height, while the other four models: EQU2215, EQU131VU, EQU231VU...