valutazioni - , GPA:
(
)
)
Produttore : Alesis
File Size : 2.21 mb
File Nome : 293cbbed-2974-4c54-ad4f-b89c999e1f6f.pdf
Lingua di insegnamento: 
Il documento viene caricato, si prega di attendere
 |
Il documento viene caricato, si prega di attendere
Facilità d'uso
Make sure all items listed on the front of this guide are in the Spitfire's box. 2. Read the Important Safety Instructions document included with the Spitfire. 3. Study the Hookup Diagram below. 4. Make sure all equipment is turned off and all gain knobs are set to zero. 5. Connect your guitar and other equipment to the Spitfire in the manner illustrated below. Refer to the Features section for details on which cables and equipment to use. 6. Plug in all devices and turn them on. 7. Experiment with the Spitfire's effect combinations. Refer to the Effect Quick Reference on the next page. 8. When finished, turn off the amp before disconnecting any equipment to prevent damage to the speaker. 9. Go to to register the Spitfire. Front Panel Input Display VALUE Knob BASS Knob MASTER VOLUME Knob Power Switch Program Up/Down EFFECT Knob DRIVE Knob TREBLE Knob HEADPHONES Jack Note: Spitfire 60 is pictured. Some of the front panel features are not found on the Spitfire 15 and 30. Rear Panel Fuse FOOTSWITCH UP/DOWN INPUTS AUX INPUT SPEAKER OUTPUT Power Cord EXPRESSION PEDAL INPUT STEREO LINK OUTPUT Spitfire Hookup Diagram Expression Pedal Front Panel Rear Panel Footswitches CD Player Amp Featur es of the Spitfir e 1. Input – plug your guitar into this 1/4" unbalanced input using a TS cable. 2. Program Up/Down Buttons – these change the program number; when pressed together, they put the unit in Bypass and Mute modes and access the tuner. 3. Display – indicates bank and program, shows parameter values and displays pitch in tuner mode. 4. EFFECT Knob – puts the Spitfire in PLAY mode or EDIT mode. You are in EDIT mode when you select a module or parameter with this knob. 5. VALUE Knob – adjusts parameter values, program numbers and master volume; stores changes. 6. DRIVE Knob – gives direct control of the DRIVE parameter found in the effect processor. 7. BASS Knob – adjusts the bass in your signal independently of the EQ effect. 8. TREBLE Knob – adjusts the treble in your signal independently of the EQ. 9. MASTER VOLUME Knob – controls the volume of the signal sent to the speaker, headphones, STEREO LINK OUTPUT and SPEAKER OUTPUT. 10. HEADPHONES Jack – plug in your headphones using a 1/ 4" stereo plug. 11. Power Switch – turns the Spitfire on and off. 12. Fuse – Replaceable fuse. See the rear panel of the Spitfire for details. 13. Power Cord – Plug this cord into a proper AC outlet. See the rear panel for details. 14. FOOTSWITCH UP/DOWN INPUT – Plug footswitches into these 1/ 4" jacks. Footswitches serve the same functions as the Program Up and Down buttons. 15. EXPRESSION PEDAL INPUT – Plug an expression pedal into this 1/4" jack for easy control over effect parameters. 16. AUX INPUT – Plug a CD player or other audio device into these RCA jacks and play along! 17. STEREO LINK OUTPUT – Use a 1/4" TS cable to connect this jack to the input of another amplifier for true stereo. 18. SPEAKER OUTPUT – Use a 1/4" TS cable to connect this jack to an external 8-ohm speaker. Effect Quick Reference Refer to chapter 10 of the User Manual for more details on effect modules. 1. COMP/LIMIT – provides increasing levels of compression (C1-C9) and limiting (L1-L9). 2. DIST – various types of distortion. 3. DRIVE – controls the drive/ gain for the DIST module; expression pedal may be used. 4. EQ – 50 separate values that cover a wide variety of EQ settings. See page 31 of the User Manual for details. 5. NR – noise reduction and hum elimination working together. The left digit of the display shows the level of hum elimination and the right digit shows the level of noise reduction. 6. CAB – settings C1 – C3 simulate 1 x 12", 2 x 12" and 4 x 10" cabinets respectively. 7. FX1 – various mono effects; most have a separate setting for pedal control. 8. PARAM – direct-control parameter for FX1; for most effects, can be set to pedal control independently of the FX1 setting. 9. FX2 – stereo versions of the effects found in FX1, with several additions; these also have settings for pedal control. 10. PARAM – direct-control parameter for FX2; for most effects, can be set to pedal control independently of the FX2 setting. 11. FX3 – various delay-based effects; most have pedal-controlled versions. 12. PARAM – direct-control parameter for FX3; for most effects, can be set to pedal control independently of the FX3 setting. 13. DIGIFX – a couple of digital- sampling effects with pedal-controlled versions. 14. LEVEL – the level of the current program. 15. ROUTE – eight variations of the routing order of all nine effect modules. Selecting, Editing and Storing Programs 1. In PLAY mode, use the Program Up and Down buttons, footswitches or VALUE knob to select a program. 2. Turn the EFFECT knob to the module or parameter you wish to edit. 3. Turn the VALUE knob to change the value of the module or parameter. 4. To store your changes, press the VALUE knob and then turn the knob to select a store location. Press the VALUE knob again to store ...