valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
PREPARATION Getting Started It’s a good idea to read all of the instructions before beginning the installation. Contents Installation Instructions.............................. 3 Wiring ........................................................ 5 Installing the Removable Faceplate .......... 6 Operating Instructions ............................... 7 CD Player Operating Instructions............ 10 MP3 Player Operation (PMP180U) ......... 12 CD Changer Controls (PMP180U) .......... 13 Care and Maintenance............................ 14 Specifications .......................................... 15 90 Day Limited Warranty......................... 16 Installation Requirements This unit is designed for installation in cars, trucks, and vans with an existing radio opening. In many cases, a special installation kit will be required to mount the radio to the dashboard. These kits are available at electronics supply stores and car stereo specialty shops. Always check the kit application before purchasing to make sure the kit works with your vehicle. If you need a kit but cannot locate one, call our customer support line at 1-800-323-4815. (U.S.A. and Canada only.) Tools and Supplies The following tools and supplies are needed to install the radio. • Torx type, flathead and Philips screwdrivers • Wire cutters and strippers • Tools to remove existing radio (screwdriver, socket wrench set or other tools) • Electrical tape • Crimping tool • Volt meter/test light • Crimp connections • 18 gauge wire for power connections • 16-18 gauge speaker wire Speaker Requirements Only connect speakers rated with a load impedance of 4 ohms. Speakers with a load impedance of less than 4 ohms could damage the unit. Disconnect Battery Before you begin, disconnect the battery negative terminal. Toll-Free Installation Assistance If you require assistance, contact Technical Support at 1-800-323-4815 from 8:30 a.m. to 7:00 p.m. EST Monday through Friday and from 9:00 a.m. to 5:00 p.m. EST on Saturday. (U.S.A. and Canada only.) 2 PCD160U/PMP180U INSTALLATION INSTRUCTIONS Installation Using a Mounting Sleeve 1. Slide the mounting sleeve off the chassis. If it is locked into position, use the removal tools (supplied) to disengage it. 2. Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is too small, carefully cut or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into the opening or cause it to bend or bow. Check for sufficient space behind the dashboard for the radio chassis. 3. Locate the series of bend tabs along the top, bottom, and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard opening, bend as many of the tabs outward as necessary to firmly secure the sleeve to the dashboard. 4. Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve. Follow the wiring diagram carefully and make certain all connections are secure and insulated with wire nuts or electrical tape. After completing the wiring connections, turn the unit on to confirm operation (vehicle ignition must be “on”). If the unit does not operate, re-check all wiring until the problem is corrected. 5. Make sure the radio is right-side up, then carefully slide the radio into the mounting sleeve until it is fully seated and the spring clips lock it into place. 6. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using the hex nut provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above or below the radio using the screw provided. Bend the strap to position it as necessary. 7. Test the radio using the Operating Instructions that follow. BEND TABS 3PCD160U AM / F M / CD R ECEIVER / CD-INCAUTION: The support strap must be used to prevent damage to the dashboard fromthe weight of the radio or improper operation due tovibration. CAUTION: For proper operationof the CD player, the chassismust be mounted within 20° of horizontal. Make sure the unit is mounted within this limitation. INSTALLATION PCD160U/PMP180U INSTALLATION INSTRUCTIONS Installation Using a Kit ISO INSTALLATION If your vehicle requires the use of an installation kit to mount this radio, follow the instructions included with the installation kit to attach the radio to the mounting plate supplied with the kit. 1. Wire and test the radio as described in step 4 of “Installation Using a Mounting Sleeve” on page 3. 2. Install the radio mounting plate assembly to the sub-dashboard according to the installation kit instructions. 3. Attach the support strap to the radio and dashboard as described in step 6 of Save all hardware and brackets as they “Installation Using a Mounting Sleeve” on will be used to mount the new radio. page 3. 2. Carefully unsnap the plastic frame from 4. Replace the dashboard trim panel. the front of the new radio chassis. Remove and discard the frame. ISO Ins...