valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
31. Currently used IP Address Firmware upload in progress Device is idle, no stream in progress Device is currently streaming Device is currently rebooting Device is being reset to its factory default settings and then rebooting FIG. 31 LCD status messages MAX-CSE/MAX-CSD10 Operation/Reference Guide Configuring Communication Configuring the MAX Communication Parameters Although the unit is initially configured to obtain the first available DHCP Address, it is recommended that after the initial connection, the unit be setup to use a Static IP Address. Using a Static IP Address for both the source and destination devices can be beneficial for both diagnostic and direct access purposes. MAX Products are not designed or intended to, and may not be used to, violate anyone’s copyright or other intellectual property rights. Each user of the MAX Products may only use the products in connection with materials legally owned or licensed by such user and only to the extent such ownership or license rights permit such use. Obtaining the unit’s initial DHCP Address 1. Connect an Ethernet cable to the unit’s rear Ethernet connector. 2. Connect the 2-pin 3.5mm mini-Phoenix PWR connector to the rear power connector and then apply power. The MAX-CSE uses the active Ethernet connection to communicate with the DHCP Server and obtain a valid DHCP Address. 3. After the unit has successfully obtained an IP Address from the DHCP Server, it then displays this obtained DHCP Address across the front LCD (FIG. 32). FIG. 32 Example of the current IP Address 4. Write down the newly obtained DHCP Address displayed on the front panel LCD. Communicating with the unit via the browser-based UI To facilitate communication with the MAX-CSE and MAX-CSD10, it is necessary for the unit to obtain a DHCP Address. Once that address is known, you can then use your web browser to access the browser- based User Interface (UI) pages and then configure the project, video, and IP connection parameters. 1. Launch your web browser. 2. Enter the IP Address of the target unit (ex: into the web browser’s Address field. 3. Press the Enter key on your keyboard to initiate the communication process and launch the initial on-screen Enter Network Password security dialog. (FIG. 33). 4. Enter the words administrator and password into the corresponding User Name/Password fields (case-sensitive). This is the factory default security login information. This login profile can later be changed. 5. Place a checkmark in the Use the Save this password in your password list selection box to save both the username and password to the MAX unit and use them as your defaults during the next new login to the target unit. .. Unchecking this "save login profile" option causes a user to have to re-enter both the username and password upon every consecutive login. Leaving this box unchecked helps add to the security feature of the unit by requiring the user to have the proper information. MAX-CSE/MAX-CSD10 Operation/Reference Guide Configuring Communication FIG. 33 Enter Network Password security dialog Save login profile selection box 6. Click OK to enter the information and proceed to the first UI page. Assigning a Static IP Address to the MAX-CSE via the browser-based UI Although the initial communication to the unit is done via a DHCP connection and since this is your source device, it is recommended that for streaming and programming purposes, you assign a Static IP Address to the unit via the browser-based UI. Located on the left side of the populated browser window is the Navigation frame which allows a user to navigate throughout the application. Located on the right side of the browser window is the Active frame which displays the pages corresponding to the currently selected option from within the Navigation frame. 1. Access the IP Settings page (FIG. 20 on page 35) by clicking the IP Settings button in the Navigation Bar. .. This page is used to assign the method of communication used by the target MAX unit. .. Note that both the default IP Configuration setting is DHCP and the corresponding read-only fields display the MAX unit’s communication parameters obtained from the DHCP Server during the initial setup. 2. Click on the Static radio box to begin entering the previously obtained Static IP Address information (typically provided by your Network Administrator). 3. Enter the corresponding Static IP Address, Subnet Mask, Gateway, and DNS parameters into their corresponding fields on this page. 4. Click the Apply button to refresh the screen and save your new communication parameters. 5. Once the browser’s progress bar indicates it has completed the temporary acceptance of the new parameters, click the Reboot button to restart the unit and incorporate these changes. 6. Once the unit powers-up, the new Static IP Address is then displayed on the LCD after the appearance of AMX logo (which can take several minutes). 7. Confirm the new communication param...
Questo manuale è adatto anche per i modelli :Ricevitore e l - MAX-CSD 10 (1.72 mb)