valutazioni - 3, GPA: 3.7
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
When the tape deck is being used, chirping or beeping sounds may result. When mounting the antenna to a column, a wall or rackB Mount the antenna so that the hinge is vertical. RQT5087 •Vinyl-covered wire {not included) \ AM ANT AM LOOP ANT I -■ -V I— - Antenna connections □ An outdoor antenna should be used when using this unit in mountainous areas or in spaces enclosed by reinforced concrete where the FM indoor antenna (included) does not provide satisfactory reception. Disconnect the FM indoor antenna if an FM outdoor antenna is installed. идя An outdoor antenna should be installed by a qualified technician only. An outdoor antenna should be used when using this unit in mountainous areas or in spaces enclosed by reinforced concrete where the AM loop antenna (included) does not provide satisfactory reception. Stretch 5-12 m (16—40 ft.) of vinyl-covered wire horizontally across a window frame or other convenient location, keeping it as high as possible from the ground. When the unit is not in use, disconnect the outdoor antenna to prevent possible damage that may be caused by lightning. Never use an outdoor antenna during an electrical storm. Be sure to connect the AM loop antenna even when an outdoor antenna is used. 13 RQT5087 Connections Speaker connections Front speakers Place the front speakers on the left and right of the TV at seated ear height so that there is good coherency between the picture and sound. Center speaker Place this speaker underneath or above the center of the TV. Aim the speaker at the seating area. Surround speakers Place these speakers on the side of or slightly behind the listener, and about one meter higher than ear level. Subwoofer The subwoofer can be placed in any position as long as it is at a reasonable distance from the TV. Note that some experimentation can yield the smoothest low frequency performance. Placement near a corner can increase the apparent output level, but can result in unnatural bass. Other connections are possible depending on your speaker system. See your speaker system’s operating instructions for details. Front speakers Front speaker (right) (not included) Front speaker (left) (not included) B” terminals For connection to a second pair of speakers. Use the A terminals to enjoy Dolby Pro Logic, SFC, and DVD 6CH INPUT. RQT5087 Bi-wiring connection идя When bi-wiring, use speakers designed for that purpose that have combined impedance of 6-8 Q 15 RQT5087 Connections Speaker connections Other speakers Subwoofer without built-in amplifier (not included) Center speaker (not included) Monaural connection cable (not included) идя For subwoofer You only need to make one of the shown connections to get sound from the subwoofer. Subwoofer with built-in amplifier (not included) Speaker impedance: Center speaker: 6-8 £i Surround speaker: 6-8 £2 Subwoofer: 6-8 Q RQT5087 El POWER —SPEAKERS— □ O □ A 0 |:liïil;lJ INPUT SELECTOR O a Selected source VOLUME iinain ^ 1 U /_ ±! SPEAKERS Basic operations Before operation, set [VOLUME] to the “MIN" position. D Press [POWER]. B Select the speaker system(s) to be used. The buttons A, B and MaviliH refer to the speaker terminals at the rear of the unit. If the button is pressed once more, the indicator will switch off and no sound will be heard from the speakers. I5iavji;n and A, or ma'flitm and B cannot both be used at the same time. Turn [INPUT SELECTOR] to select and start the desired source. (Refer to the appropriate operating instructions for details.) The indicator corresponding to the selected source lights and the source is shown on the display. The selected source and “INPUT will be shown on the display. TAPE (MONITOR): To listen to cassette tapes VCR 1: To watch video tapes (VCR 1) TWDSS/VCR 2: To watch TV, DSS or video tapes (VCR 2) VCR 3: To watch video tapes (VCR 3) DVD: To watch DVD CD: To listen to compact discs TUNER: To listen to radio broadcasts PHONO: To listen to phono discs mm To wal TV mo □ Adjust the volume level. To watch a video (or DVD) or the TV, set the TV to either the TV mode or VIDEO mode. For your reference • If a Dolby Pro Logic or SFC mode has been selected After displaying the selected source, the display will then change to show the Dolby Pro Logic or SFC mode and “INPUT" will go out (^ page 24). If the source chosen was TUNER then the display will change again to show the frequency. ■ If you are using VCR and you select TAPE, CD, TUNER, or PHONO The picture will remain on the screen. • The volume control The volume control on this unit allows more gradual adjustment compared to past models, thus making it easier to make fine volume adjustments during normal use. When you finish listening Be sure to reduce the volume level, and switch the power to the standby condition by pressing [POWER]. i I .y 8 CQ c £ * C c Ô 17 RQT5087 о ТАРЕ (MONITOR) push open / * о О о Г- Pf (Î...