valutazioni - 5, GPA: 4.2
(
)
)
|
Foto e specifiche Yamaha R-S300 |
Facilità d'uso
See page 11 for details. • Do not let bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or the speakers. Turntable For information about other components that Speakers A Audio out u out © © C@) i ^ □ □ CD player DVD player, etc. CD recorder, Subwoofer etc. Speakers B y • The PHONO jacks are designed for connecting a turntable with an MM cartridge. • Connect your turntable to the GND terminal to reduce noise in the signal. However, for some turntables, you may hear less noise without the GND connection. 10 En CONNECTIONS ■ IMPEDANCE SELECTOR switch CAUTION Do not change the IMPEDANCE SELECTOR switch while the power of this unit is turned on, as doing so may damage the unit. If the unit fails to turn on, the IMPEDANCE SELECTOR switch may not be fully slid to either position. If this is the case, remove the power cable and slide the switch all the way to either position. Select the switch position (LOW or HIGH) according to the impedance of the speakers in your system. Switch position Impedance level HIGH • If you use one set (A or B), the impedance of each speaker must be 8 O or higher. • If you use two sets (A and B) simultaneously, the impedance of each speaker must be 16 O or higher. • If you make bi-wire connections, the impedance of each speaker must be 8 O or higher. See page 11 for Bi-wire connection. LOW • If you use one set (A or B), the impedance of each speaker must be 4 O or higher. • If you use two sets (A and B) simultaneously, the impedance of each speaker must be 8 O or higher. • If you make bi-wire connections, the impedance of each speaker must be 4 O or higher. See page 11 for Bi-wire connection. ■ Bi-wire connection Bi-wire connection separates the woofer from the combined midrange and tweeter section. A bi-wire compatible speaker has four binding post terminals. These two sets of terminals allow the speaker to be split into two independent sections. With these connections, the mid and high frequency drivers are connected to one set of terminals and the low frequency driver to another set of terminals. This unit ■ Connecting speaker cables Connect the other speaker to the other set of terminals in the same way. CAUTION When making bi-wire connections, set the IMPEDANCE SELECTOR switch to HIGH or LOW depending on the impedance of your speakers: 8 Q or higher: HIGH 4 Q or higher: LOW See page 11 for more information about the IMPEDANCE SELECTOR switch. Note Remove approximately 10 mm (3/8 in) of insulation from the end of each speaker cable. Note When inserting speaker cables into the speaker terminals, insert only the bare speaker wire. If insulated cable is inserted, the connection may be poor and sound may not be heard. When making bi-wire connections, remove the shorting bridges or cables on the speaker. y To use the bi-wire connections, press SPEAKERS A and SPEAKERS B on the front panel or on the remote control so that both SP A and B light up on the front panel display. SLEEP O © DHEt o A SUKB6 B 9 9 PHONO O TAPE o CD o DOCK O LINE 1 o UNE 2 o SPEAKERS A/B 11 En CONNECTIONS Connecting the FM and AM antennas Indoor antennas for receiving FM and AM broadcasts are included with this unit. In general, these antennas should provide sufficient signal strength. Connect each antenna correctly to the designated terminals. Note If you experience poor reception quality, install an outdoor antenna. Consult the nearest authorized Yamaha dealer or service center about outdoor antennas. ^ Outdoor FM antenna Indoor FM antenna (included) Outdoor AM antenna Use 5 to 10 m of vinyl-covered wire extended outdoors from a window. AM loop antenna (included) The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit. The AM loop antenna should be placed away from this unit. Ground (GND terminal) For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth. ■ Assembling the supplied AM loop antenna ■ Connecting the wire of the AM loop antenna Connecting power cable Plug the power cable into the AC wall outlet after all other connections are complete. 12 En PLAYING AND RECORDING CAUTION Extreme caution should be exercised when you play back CDs encoded in DTS. If you play back a CD encoded in DTS on a CD player that does not support DTS, only noise will be heard, and this noise may damage your speakers. Check whether your CD player supports CDs encoded in DTS. Also, check the sound output level of your CD player before you play back a CD encoded in DTS. Playing a source ®©©®@®@©@© □ © rp □ 1, I, .1. ■:!; Olh SPEAKERS A/B A (power) INPUT selector VOLUME 3 Press SPEAKERS A and/or SPEAKERS B on the front panel or on the remote control to select speakers A and/or speakers B. When speaker set A or speaker set B are turned on,...