valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
If the CD player, turntable and tape deck connected to this unit are YAMAHA components designed for remote control compatibility, then this remote control transmitter will also control various functions of each component. KEY FUNCTIONS For Control of This Unit PLAY DECK A/B STOPREC/PAUSE REC MUTE DIR A DIR B TAPE 1 TAPE 2 AUX +– VOLUME – PRESET + A/B/C/D/E TUNER SEARCH SKIP PAUSE/STOP DISC STOP PLAY CD PHONO SLEEP POWER Turns the power on/off. The power to the receiver is automatically turned off one hour after this key is pressed (so that “SLEEP” lights up on the display). Selects input source. Turns the volume level up/down. Selects preset station number + : Selects higher preset station number. – : Selects lower preset station number. A/B/C/D/E: Selects the page (A – E) of preset stations. For Other Component Control Identify the remote control transmitter keys with your component’s keys. If these keys are identical, their function will be the same. On each key function, refer to the corresponding instruction on your component’s manual. PLAY DECK A/B STOPREC/PAUSE REC MUTE DIR A DIR B TAPE 1 TAPE 2 AUX +– VOLUME – PRESET + A/B/C/D/E TUNER SEARCH SKIP PAUSE/STOP DISC STOP PLAY CD PHONO SLEEP POWER Controls compact disc player. * DISC SKIP is applicable only to a compact disc changer. Controls tape deck. * DIR A, B and DECK A/B are applicable only to a double cassette tape deck. * For a single cassette deck with automatic reverse function, pressing DIR A will reverse the direction of tape running. Standby mode While the power is on, pressing the POWER key on the remote control transmitter switches the unit to the Standby mode. (In this mode, the indicator is half illuminated.) Note The POWER switch on the front panel of this unit should be turned off when left unused for a long period of time. POWER on mode Standby mode NOTES ABOUT THE REMOTE CONTROL TRANSMITTER Battery installation Remote control transmitter operation range 1 2 3 Battery replacement If you find that the remote control transmitter must be used closer to the main unit, the batteries are weak. Replace both batteries with new ones. Notes . Use only AA, R6, UM-3 batteries for replacement. . Be sure the polarities are correct. (See the illustration inside the battery compartment.) . Remove the batteries if the remote control transmitter will not be used for an extended period of time. . If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. 30° 30° Remote control sensor Within approximately 6 m (19.7 feet) Notes . There should be no large obstacles between the remote control transmitter and the main unit. . If the remote control sensor is directly illuminated by strong lighting (especially an inverter type of fluorescent lamp etc.), it might cause the remote control transmitter not to work correctly. In this case, reposition the main unit to avoid direct lighting. TROUBLESHOOTING If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center for help. English SYMPTOM CAUSE REMEDY AmplifierThe unit fails to turn on when the POWER switch is pressed. Power cord is not plugged in or is not completely inserted. Firmly plug in the power cord. No sound. Incorrect output cord connections. Connect the cords properly. If the problem persists, the cords may be defective. Appropriate input source is not selected. Select an appropriate input source with the INPUT selector. The TAPE 2 MONITOR switch is ON. Press the TAPE 2 MONITOR switch to turn it off. The sound suddenly goes off. The protection circuit has activated because of short circuit etc. Turning the unit off and then on will reset the protection circuit. The SLEEP timer functioned. Cancel the SLEEP timer function. Only one side speaker outputs the sound. Incorrect setting of the BALANCE control Adjust it to the appropriate position. Incorrect cord connection. Connect the cords properly. If the problem persists, the cords may be defective. Sound “hums”. Incorrect cord connections. Firmly connect the audio plugs. If the problem persists, the cords may be defective. No connection from the turntable to the GND terminal. Make the GND connection between the turntable and this unit. The volume level is low while playing a record. The record is being played on a turntable with an MC cartridge. The player should be connected to the receiver through the MC head amplifier. The volume level cannot be increased, or sound is distorted. The power to the component connected to the REC OUT terminals of this unit is off. Turn the power to the component on. Using the BASS, TREBLE and BALANCE controls does not affect the t...