valutazioni - 4, GPA: 4.5
(
)
)
|
Facilità d'uso
If you experience poor reception quality, an outdoor antenna may result in improvement. FM ANT AM ANT GND 75W UNBAL. Outdoor FM antenna Outdoor AM antenna AM loop antenna (included) 75-ohm/300-ohm antenna adapter 75-ohm/300-ohm antenna adapter 75-ohm coaxial cable 300-ohm feeder Indoor FM antenna (included) Ground Connecting the AM loop antenna 1 2 3 * The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall. * The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit. A A A Orient so that the best reception is obtained. GND terminal For maximum safety and minimum interference, connect the GND terminal to a good earth ground, which is a metal stake driven into moist earth. Notes . When connecting the indoor FM antenna, insert its connector into the FM ANT terminal firmly. . If you need an outdoor FM antenna to improve FM reception quality, either 300-ohm feeder or coaxial cable may be used. In locations troubled by electrical interference, a coaxial cable is preferable. CONTROLS AND THEIR FUNCTIONS FRONT PANEL RX-496RDS and RX-496 123 456 STANDBY/ON NATURAL SOUND STEREO RECEIVER SPEAKERSPHONES A ON B OFF BASS TREBLE BALANCE VOLUME PURE DIRECT 5 5 4 3 2 l 0 l 2 3 4 5 5 4 3 2 l 0 l 2 3 4 L R l6 20 28 40 60 l2 8 4 2 0 –dB 5 5 4 3 2 l 0 l 2 3 4 FM/AM MAN’L/AUTO FM TUNING MODE AUTO/MAN’L MONO DOWN TUNING UP MEMORY EDIT A/B/C/D/E 1 2 3 4 5 6 7 8 TUNER CDPHONO AUX TAPE 1/MDTAPE 2 MONITOR RDS MODE/FREQ EON MODE START PTY SEEK LOUDNESS 5 6 7 4 3 2 l FLAT l0 –30dB 9 8 7890AIJLDEFGCB HK : RX-496RDS only RX-396RDS and RX-396 123 46 STANDBY/ON NATURAL SOUND STEREO RECEIVER SPEAKERSPHONES A ON B OFF BASS TREBLE BALANCE VOLUME 5 5 4 3 2 l 0 l 2 3 4 5 5 4 3 2 l 0 l 2 3 4 L R l6 20 28 40 60 l2 8 4 2 0 –dB 5 5 4 3 2 l 0 l 2 3 4 LOUDNESS 5 6 7 4 3 2 l FLAT l0 –30dB 9 8 FM/AM MAN’L/AUTO FM TUNING MODE AUTO/MAN’L MONO DOWN TUNING UP MEMORY EDIT A/B/C/D/E 1 2 3 4 5 6 7 8 TUNER CDPHONO AUX TAPE 1/MDTAPE 2 MONITOR RDS MODE/FREQ EON MODE START PTY SEEK 7890AIJLDEFGCB HK : RX-396RDS only English 1 STANDBY/ON switch Press this switch to turn on the power to this unit. Press it again to turn this unit into the standby mode. Standby mode In this state, this unit consumes a very small quantity of power to receive infrared-signals from the remote control transmitter. 2 Remote control sensor Receives signals from the remote control transmitter. 3 Display panel Shows various information. (For details, refer to page 13.) 4 Input selector buttons Select a program source to listen to. When a button is pressed, the name of the selected source appears on the display. 5 PURE DIRECT switch and indicator RX-496RDS and RX-496 only Press this switch so that the indicator lights up to listen to a source in the purest sound. (Refer to page 16 for details.) 6 VOLUME control Used to raise or lower the volume level. 7 PHONES jack PHONES When you listen with headphones, connect the headphones to the PHONES jack. When listening with headphones privately, set both the SPEAKERS A and B switches to the OFF position. 8 SPEAKERS switches Set the switch A or B (or both A and B) for the speaker system (connected to this unit) you will use to the ON position. Set the switch for the speaker system you will not use to the OFF position. 9 A/B/C/D/E button Press this button to select a desired group (A–E) of preset stations. 0 Preset station number selector buttons Select a preset station number (1 to 8). A Tone controls BASS Used to increase or decrease the low frequency response. The 0 position produces flat response. TREBLE Used to increase or decrease the high frequency response. The 0 position produces flat response. B BALANCE control Adjusts the balance of the output volume to the left and right speakers to compensate for sound imbalance caused by speaker location or listening room conditions. C Continuously variable LOUDNESS control Used to compensate for the human ears’ loss of sensitivity to high and low-frequency ranges at low volume. D RDS MODE/FREQ button RX-496RDS and RX-396RDS only When an RDS station is received, pressing this button changes the display mode into the PS mode, PTY mode, RT mode and/or CT mode (if the station employs these RDS data services), and frequency display in turn. E PTY SEEK MODE button RX-496RDS and RX-396RDS only When this button is pressed, the unit turns into the PTY SEEK mode. F PTY SEEK START button RX-496RDS and RX-396RDS only Press this button to begin searching for a station after the desired program type is selected in the PTY SEEK mode. G EON button RX-496RDS and RX-396RDS only Press this button to select a desired program type (NEWS, INFO, AFFAIRS, SPORT) when you want to call a radio program of that program type automatically. H FM/AM button Press this button to switch the reception band to FM or AM. I MEMORY (MAN’L/AUTO FM) button When this button is pressed, the “MEMO” indicator flashes for about 5 seconds. While the indicator is fl...
Questo manuale è adatto anche per i modelli :Ricevitore e l - RX-396 (1.51 mb)
Ricevitore e l - RX-496 (1.51 mb)
Ricevitore e l - RX-496RDS (1.51 mb)