valutazioni - 5, GPA: 3.6
(
)
)
|
Facilità d'uso
keys function as P.CALL keys. Use to turn the receiver on and off. & AUTO key ) 4/. keys ! DVD POWER key Use to select the auto tuning mode. If CD or MD is selected as the input source, Used to operate DVD player. 7 key these keys function as skip keys. For details, refer to the instruction manual of If CD or MD is selected as the input source, this 5 TUNING 1/. keys your DVD player.(Press the DVD key for key functions as the stop key. If tuner is selected as the input source, these more than 2 seconds.) * 8 key keys function as tuning keys. @ RECEIVER key Use to operate other components. If CD or MD is selected as the input source, Use to return to the operation of the receiver. ( VOLUME keys & these keys function as search keys. # TITLE key Use to adjust the receiver volume. 6 BASS BOOST key & Use to operate other components. Use to select the maximum adjustment set-RDS operation keys .. ting for the low frequency range. Use to receive RDS broadcasts. Setting up the system Preparations Make connections as shown below. Connecting audio componentsWhen connecting the related system components, be sure to also refer to the instruction manuals supplied with the components you are connecting. Shape of AC outlets Do not connect the power cord to a wall outlet until all connections are completed. DTS disclaimer clause SYSTEM CONTROL DTS Digital Surround™ is a discrete 5.1 channel digital audio format available on CD, LD, and DVD software which consequently cannot be decoded and played back inside most CD, LD, or DVD players. For this reason, when DTS-encoded software is played back through the analog outputs of the CD, LD, or DVD player, excessive noise will be exhibited. To avoid possible damage to the audio system, proper precautions should taken by the consumer if the analog outputs are connected directly to an amplification system. To enjoy DTS Digital Surround™ playback, an external 5.1 channel DTS Digital Surround™ decoder system must be connected to the digital output (S/P DIF, AES/EBU, or TosLink) of the CD, LD or DVD player. The only audio product model incorporating the DTS Digital Surround decoder is the KRF-V7030D. VIDEO 2/MONITOR jacks (for KRF-V6030D/V5030D/V4530D) The receiver’s VIDEO 2/MONITOR jacks can be used in two different ways. Make the appropriate setting for the component connected to the jack when the receiver is turned on. Use as a VIDEO 2 jack You can connect a video deck or the like to these jacks and perform video playback and recording. The initial factory setting is “VIDEO 2.. Use as a MONITOR jack You can connect a cassette deck or the like to these jacks and make use of the deck’s monitoring function during recording. Alternately, you can connect a graphic equalizer to these jacks to apply compensation to the music signal. To use the VIDEO 2/MONITOR jacks as MONITOR jacks, hold down the MONITOR key of the main unit for more two seconds so that the indication shown below appears. • At the same time the setting is switched to “MONITOR,” the audio input source switches to tuner and the video input source switches to VIDEO 1. • To switch the setting back to “VIDEO 2,” once again hold down the MONITOR key for two seconds or more. STEREO ST. MEMO SW RLSP A MONITOR MONITOR Notes 1. Be sure to insert all connection cords securely. If their connections are imperfect, the sound may not be produced or noise may interfere. 2. Be sure to remove the power cord from the AC outlet before plugging or unplugging any connection cords. Plugging/unplugging connection cords without disconnecting the power cord can cause malfunctions and may damage the unit. 3. Do not connect power cords from components whose power consumption is larger than what is indicated on the AC outlet at the rear of this unit. Analog connections Audio connections are made using RCA pin cords. These cables transfer stereo audio signal in an “analog” form. This means the audio signal corresponds to the actual audio of two channels. These cables usually have 2 plugs each end, one red for the right channel and one white for the left channel. These cables are usually packaged with the source unit, or are available at your local electronics retailer. MONITOR PLAY INPLAY IN REC OUT AUDIO L R MD/TAPE1CD/DVDPHONO GND REC OUT To AC wall outlet Cassette deck or MD recorder CD player IN OUT jacks @ Video component, 3 head cassette deck, or Graphic equalizer * IN OUT OUT OUT VIDEO2/MONITOR jacks (KRF-V6030D/ V5030D/V4530D only) You can connect an equalizer in Monitor mode, or a video com- ponent in Video 2 mode. Record player U. K. Other countries When you connect the video component to the VIDEO2/MONITOR jacks, connect the video cord (yellow RCA pin cords) of the connected component to the VIDEO2 IN jack (KRF-V6030D/V5030D/V4530D only). Setting up the system Connecting video components Connecting a DVD player (6-channel input) If you have connected a DVD player to the receiver with digital connection, be sure to read the “Input mode setting...
Questo manuale è adatto anche per i modelli :Ricevitore e l - KRF-V4530D (688.64 kb)
Ricevitore e l - KRF-V6030D (688.64 kb)
Ricevitore e l - KRF-V7030D (688.64 kb)