valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
• When subwoofer output sound is required, select “FRNT NML”. 3 Press the SET UP key to accept the setting. • The front speakers setting indication (FRNT) appears. SW RLSP A STEREO 4 Use the MULTI CONTROL keys to select the appropriate front speakers setting. 1 FRNT NML (normal): Average size front speakers are connected to the receiver. 2 FRNT LRG (large): Large front speakers are connected to the receiver. • For “FRNT LRG” selection, no sound will be heard from SUBW even when it is set to ON. However, if you select CINEMA EQ. when subwoofer is selected, you will be able to hear sound from the subwoofer. When in STEREO mode, the sound goes directly to front speaker. 5 Press the SET UP key to accept the setting. • The center speaker setting indication (CNTR) appears. 6 Use the MULTI CONTROL keys to select the appropriate center speaker setting. If you selected “LRG” as the front speakers setting, 1 CNTR LRG (large): A large center speaker is connected to the receiver. 2 CNTR NML (normal): An average size center speaker is con nected to the receiver. 3 CNTR OFF: Center speaker setting mode to the receiver is OFF. If you have selected “NML” as the front speakers setting, 1 CNTR ON: Center speaker setting mode to the receiver is ON. 2 CNTR OFF: Center speaker setting mode to the receiver is OFF. 7 Press the SET UP key again to accept the setting. • The surround speaker setting indication (SURR) appears. Preparations 8 Use the MULTI CONTROL keys to select the appropriate surround speaker setting. If you selected “LRG” as the center speaker setting, 1 SURR LRG (large): Large surround speakers are connected to the receiver. 2 SURR NML (normal): Average size surround speakers are connected to the receiver. 3 SURR OFF: Surround speaker setting mode to the receiver is OFF. If you have selected other than “LRG” as the center speaker setting, 1 SURR ON: Surround speaker setting mode to the receiver is ON. 2 SURR OFF: Surround speaker setting mode to the receiver is OFF. Press the SET UP key again to accept the setting. • The receiver enters the speaker volume level adjustment mode. • In steps 3 and 4, indications appear only for the selected channels of the speakers that require adjusting. 3Adjust the speaker volume. From your usual listening position, adjust the volume levels. The volume levels from each speaker should be the same. 1 Use the MULTI CONTROL keys to adjust the volume of the test tone output from the speaker channel to be adjusted. The channel indication blinks while the test tone is being output. LSP A The test tone is heard from the speakers in the following sequence for 2 seconds each: = L = C = R = SR = SL = SW • If you change the volume level settings for the speakers while listening to music, the settings referred to on this page are also changed. • • If the speaker setting selects are changed, the speaker level settings are reset. 2 Press the SET UP key. • The test tone is turned off. The receiver enters the mode for inputting the distance to the speakers. Continued to next page Preparing for surround sound 4Input the distance to the speakers. 20 1 Measure the distance from the listening position to each of the speakers. Jot down the distance to each of the speakers. Distance to front speakers: ____ feet____ meters Distance to center speaker: ____ feet____ meters Distance to surround speakers: ____ feet____ meters 2 Use the MULTI CONTROL keys to select the distance to the front speakers. The speaker indicator to be adjusted blinks. LSP A R STEREO Indication in feet Indication in meters • The allowable setting range is 1 to 30 feet (0.3 to 9.0 m), adjustable in 1 foot (0.3 m) increments. 3 Press the SET UP key to accept the settings. 4 Repeat steps 2 and 3 to input the distance for each of the speakers. 5 Setup is complete when the input indication reappears. SP R A L SW Operations Display when all speakers have been selected. • The speakers you have selected should appear on the display. Confirm that all the speakers have been correctly selected. Input level adjustment (analog sources only) If the input level of an analog source signal is too high, adjust the input level. The CLIP indicator will blink to indicate the source signal. CLIP 1 Use the INPUT SELECTOR knob to select the source which input level you want to adjust. • You can store a separate input level for each input source. If the MONITOR function is ON, you can store an input level for when MONITOR is on independently of the input levels for the input sources. 2 Press the SOUND key repeatedly until the “INPUT” indication appears. 3 Use the MULTI CONTROL keys to adjust the input level. LSP A R STEREOSW • The adjustment mode is displayed for approximately eight seconds. • The input level may be adjusted to any one of three settings: 0dB, -3dB, and -6dB. (The initial setting is 0dB.) 4 Press the SOUND key again to return to the input indication. Normal playback Preparing for playback Some preparatory steps are needed before starting playb...
Questo manuale è adatto anche per i modelli :Ricevitore e l - KRF-V5050D (2.92 mb)
Ricevitore e l - KRF-V5550D (2.92 mb)
Ricevitore e l - VR-505 (2.92 mb)
Ricevitore e l - VR-506 (2.92 mb)