valutazioni - 4, GPA: 5
(
)
)
|
Foto e specifiche Cambridge Audio AZUR 650R |
Facilità d'uso
Stereo Mono When listening to FM, press to alternate between stereo and mono modes. Store Press to store the current frequency when in Tuner mode. Mode Press to select Auto/Manual or Preset tuning when in Tuner mode. Enter Vol Vol AnalogDirect 7.1 Direct DD DTS Dynamic Stereo Modes PL IIx Neo/DSP Sub On/Off Store Mode Video 1BD DVD Tuner AM/FM Video In Type LipSync Audio In Type Bass Treble Video 2 Rec 1 Aux CD Rec 2 Stereo Mono Display PTY APS Mute Mutes the audio on the AV Receiver. Press again to cancel mute. Volume Increase or decrease the volume of the AV receiver output. Also used as up/down in the OSD setup menus. Tune / Left & Right Press the right arrow to increase tuner frequency/change preset. Press the left arrow to decrease tuner frequency/change preset. Also used to scroll left/right in the OSD setup menus. Enter Used in the OSD setup menus. On-Screen Display (OSD) Press to turn on and off the on-screen setup menus for display on your monitor/screen. Bass/Treble Press for bass/treble adjustment, using the Volume up/down buttons. Note: Bass/Treble is bypassed in analogue stereo direct and 7.1 direct modes. 7.1 Direct Selects the 5.1/6.1/7.1 direct input. Audio In Type Switches the audio between the types available for the current source. Depending on the source selected and whether you have assigned an HDMI input to it, Analogue, Digital and HDMI can be available. Video In Type Switches the video between the types available for the current source. Depending on the source selected and whether you have assigned an HDMI input to it, Composite, S-Video, Component and HDMI types can be available. Note: The 650R cannot simultaneously receive HDMI audio and analogue video from the same source. For any HDMI audio sources selecting analogue video will then cause the unit to switch to analogue audio as well. Digital audio via SPDIF/Toslink can then also be selected via the Audio Input Type button but not HDMI audio. Returning to HDMI video will allow selection of HDMI audio (or indeed analogue or digital audio) again. Lip sync Press to activate and adjust the lip sync delay function if the audio and video appear out of sync. While the Lip sync delay status is shown on the units display, use the Vol and Vol buttons to adjust the delay time. Adjusting the value to zero causes lip sync delay to be turned off. See later section in this manual. Tuner AM/FM, BD/DVD, Video 1, Video 2, Rec 1, Aux, CD, Rec 2 Press the corresponding button to change the input source. Pressing the Tuner AM/FM button a second time toggles between AM and FM modes. The above button descriptions are naturally brief. Please refer to the ‘Operating Instructions’ section of this manual for more information on the relevant functions implemented. azur 650R 9 Front panel display Tuner mode indicators Shows Memory/Store active, Stereo mode active, AutoScan active and RDS On. Tone control indicator Lights when Bass and Treble controls are active. Direct indicator Lights when the 650R is in a Direct mode - Analogue Stereo Direct or 7.1 Direct. HDMI Indicates the current source audio input type is HDMI. Multi Indicates the 650R is receiving multi-channel PCM over HDMI Frequency type Indicates the tuned frequency in AM or FM Tuner mode. Decoding mode indicators Shows the current decoding mode, Dolby Digital, DTS etc. In conjunction with the Output Channel indicators these give full details of the current processing mode. Main information display Shows the current source selected, also the surround mode and station name/frequency when in tuner mode etc. Balance indicator Lights when the Front Left and Right speaker outputs have been set to different levels in the OSD, i.e. a balance adjustment has been made. Digital/Analogue indicators Indicates the current source audio input type is Digital (SPDlF/Toslink) or Analogue. Output channel indicators Shows the currently active channels depending on decoding mode and source material. Icons lit indicate active channels in the source material. Icons with a box around them indicate actual channels being output by the 650R. Display examples - Indicates a 5.1 Dolby Digital source being played back as 5.0 (Sub off). The lit LFE indicates a low frequency effects channel is present in the source material. When this icon isn’t boxed it indicates the LFE channel is not being sent to a subwoofer but will be mixed into the front left and right instead. - Indicates a 7.1 playback of DTS ES material. - Indicates a 2.1 output created in the digital domain from analogue input material. 1 2 3 4 5 6 7 8 9 10 11 1 2 3 8 9 10 11 6 7 To avoid damaging the speakers with a sudden high-level signal, be sure to switch the power off before connecting the speakers. Check the impedance of your speakers. Speakers with an impedance of between 4 and 8 ohms (each) are recommended. The coloured speaker terminals are positive (+) and the black speaker terminals are negative (-). Make sure correct polarity is maintained at each speaker c...