The correction value can be checked using the STATUS button. Offset -4dB The figure is the correction value when the standard level is corrected. ENGLISH Get GetGetting Star ting Starting Start tted eded Connections ConnectionsConnections Set SetSetup upup Pla PlaPlaybac ybacyback kk Remot RemotRemote Contr e Contre Control olol Multi-Zone Multi-ZoneMulti-Zone Inf InfInfor orormation mationmation T TTr rroubleshooting oubleshootingoubleshooting SOURCE SELECT INPUT MODE MASTER VOLUME BAND TUNING DIMMER STATUS VIDEO SELECT About the button names in these explanations < > : Buttons on the main unit [ ] : Buttons on the remote control unit Button name only: Buttons on the main unit and remote control unit [OFF] VIDEO SELECT SOURCE SELECT [MODE SELECTOR 1] [MODE SELECTOR 2] [ON/SOURCE] MASTER VOLUME [MUTING] STATUS DIMMER [TUNER] SOURCE SELECT TUNING [MODE] [TUNER] BAND INPUT MODE [Front] [Rear] Playback Preparations Turning the Power On 1 1 Press . The power indicator lights red and the power is set to the standby mode. 2 2 Press or [ON/SOURCE]. The power indicator flashes green and the power turns on. Turning the Power Off qPress or [OFF]. The power is set to the standby mode. wPress . The power indicator turns off, and so does the power. NOTE Power continues to be supplied to some of the circuitry even when the power is in the standby mode. When leaving home for long periods of time or when traveling, either press to turn off the power, or unplug the power cord from the power outlet. Selecting the Input Source Operation on the main unit Turn . If “Rec Select” is selected for the input source, press before turning . Operation on the main remote control unit Press [SOURCE SELECT]. The desired input source can be selected directly. Setting the Input Mode Set the input mode for this source. Press INPUT MODE. The INPUT mode indicator lights (AUTO, PCM, DTS mode). AUTO PCM DTS EXT. IN. ANALOG bPress to select “ANALOG”, to select “EXT. IN”. [Selectable items] AUTO : Detect type of digital input signal and decode and play automatically. : Decode and play only PCM input signals. PCMDTSANALOGEXT. IN : Decode and play only DTS input signals. : Play only signals from analog input. : Play only signals from EXT. IN input. • When a digital signal is properly input, the “ ” indicator lights on the display. If the “ ” indicator does not light, check the digital input connector assignment and the connections. • The surround mode cannot be set if the input mode is set to “EXT. IN”. • Only set “PCM” and “DTS” when playing the respective signals. Operations During Playback Adjusting the Master Volume Either turn or press [MASTER VOLUME]. ENGLISH Turning Off the Sound Temporarily (Muting) Press [MUTING]. To cancel, press [MUTING] again. Muting can also be canceled by adjusting the master volume. Listening with Headphones Plug the headphones into . The sound from the speakers and pre-out connectors is automatically cut. NOTE Be careful not to set the volume too high when using headphones. Switching the front speakers Press . Video Select Function Switch video input source while listening to audio signal. Press VIDEO SELECT until the desired picture appears. bTo cancel, press VIDEO SELECT to select “SOURCE”. Checking the currently playing program source, etc. Press STATUS. The current program source and various settings are indicated on the display. For details, refer to “Information” (vpage 34). Switching the brightness of the display Press [DIMMER]. Bright Dim OFF Dark Playing Video and Audio Equipment Basic Operation 1 1 Prepare the equipment. qLoad the DVD, CD or other software in the player. (vSee the operating instructions of the respective devices.) wTo play a video device, switch the monitor input. (vSee the monitor’s operating instructions.) 2 2 Use SOURCE SELECT to select the input source. 3 3 Set [MODE SELECTOR 1] to “AUDIO” or “VIDEO”. (vpage 43 “Remote Control Unit Operations”) 4 4 Set [MODE SELECTOR 2] to the component you want to operate. Listening to FM/AM Broadcasts Basic Operation 1 1 Either turn or press [TUNER] to select “TUNER”. 2 2 Set [MODE SELECTOR 1] to “AUDIO”. (vpage 43 “Remote Control Unit Operations”) 3 3 Press BAND to select “FM” or “AM”. 4 4 Tune in the desired broadcast station. qTo tune in automatically (Auto Tuning) Press [MODE] to light the “AUTO” indicator on the display, then use TUNING to select the station you want to hear. wTo tune in manually (Manual Tuning) Press [MODE] to turn off the display’s “AUTO” indicator, then use TUNING to select the station you want to hear. • It is also possible to switch to “FM” or “AM” in step 1 by pressing [TUNER]. • If the desired station cannot be tuned in with auto tuning, tune it in manually. • When tuning in stations manually, press and ho...
)
