valutazioni - 4, GPA: 3.8
(
)
)
|
Facilità d'uso
• The stored signals are transmitted successively. Punch Through (1) Punch through button Buttons used in the CD, CDR, TAPE, DVD, VDP, VCR1 and VCR2 modes can be assigned to the buttons shown on the diagram at the right which are not normally used in the AMP, TV, DBS and CABLE modes. For example, when the CD mode is set to the punch through mode in the AMP mode, the CD mode’s PLAY, STOP, MANUAL SEARCH, AUTO SEARCH, PAUSE and DISC SKIP buttons’ signals are sent in the AMP mode. (2) Making the punch through setting 1 1 Press the power ON/SOURCE button and the OFF button at the same time. • “PRE” appears on the remote control unit’s display. 2 2 Use the • and . cursor buttons to display “PUNCH” on the remote control unit, then press the ENTER button. • “SEL” appears on the remote control unit’s display. 3 3 Use the • and . cursor buttons to display the mode for which you want to make the punch through setting, then press the ENTER button. • “SEL” appears on the remote control unit’s display. The display switches as shown below each time the • and . cursor buttons are pressed. AMP DBS CABLE TV It is also possible to select the mode directly using the mode buttons. 1 DVD 1 (1) 2, 3, 4 2, 3, 4 4 4 Use the • and . cursor buttons to display the mode you want to punch through, then press the ENTER button. • “OK” is displayed and the punch through is set. The display switches as shown below each time the • and . cursor buttons are pressed. CD CDR MD TAPE DVD VCR2 VCR1 VDP It is also possible to select the mode directly using the mode buttons. 42 Resetting Setting the back light’s lighting time DVD 2, 3 1 1 2, 3 1 2 Press the power ON/SOURCE button and the OFF button at the same time. • “PRE” appears on the remote control unit’s display. Use the • and . cursor buttons to display “BKLT” on the remote control unit, then press the ENTER button. • “05SEC” appears on the remote control unit’s display. 3 Use the • and . cursor buttons to adjust the lighting time (3 sec ~ 30 sec), then press the ENTER button. • “OK” is displayed and that lighting time is set. (1) Resetting the preset memory DVD 2, 3, 4 1 1 2, 3, 5 1 2 Press the power ON/SOURCE button and the OFF button at the same time. • “PRE” appears on the remote control unit’s display. Use the • and . cursor buttons to display “RST” on the remote control unit, then press the ENTER button. Use the • and . cursor buttons to display “PRE” on the When the mode you want to reset is shown on the remote remote control unit, then press the ENTER button. control unit’s display, press the ENTER button to reset the 3 5 • After “SEL”is displayed on the remote control unit’s preset memory. display, the registered preset memory is displayed on the •The LCD’s back light flashes during the resetting operation, remote control unit’s display. and when the operation is completed, “OK”is displayed and the set returns to the normal operating mode. Use the • and . cursor buttons to select the code to be reset. (2) Resetting “learned” buttons Press the power ON/SOURCE button and the OFF button at the same time. 1 1 1 •“PRE”appears on the remote control unit’s display. 2, 3, 4 3 3 Use the • and . cursor buttons to display “LRN”on the remote control unit’s display, then press the ENTER button. •“SEL”is displayed. DVD 2, 3, 4 4 4 Use the • and . cursor buttons to select the mode of the button to be reset, then press the ENTER button. • The LCD’s back light flashes during the resetting operation, and when the operation is completed, “OK”is displayed and the set returns to the normal operating mode. 2 2 Use the • and . cursor buttons to display “RST”on the remote control unit’s display, then press the ENTER button. •“PRE”is displayed. (3) Resetting the system call buttons Press the power ON/SOURCE button and the OFF button at the same time. •“PRE”appears on the remote control unit’s display. 1 DVD Use the • and . cursor buttons to display “RST”on the remote control unit, then press the ENTER button. •“PRE”appears on the remote control unit’s display. 2, 3, 4 3 3 Use the • and . cursor buttons to display “CALL”on the remote control unit, then press the ENTER button. •“SEL”appears on the remote control unit’s display. 2, 3, 5 4 4 Press the • and . cursor buttons to select the system call setting to be reset. The remote control unit’s display switches as shown below each time the • and . cursor buttons are pressed. SYS CALL 1 SYS CALL 2 5 5 To reset CALL 1 or CALL 2, select “CALL 1”or CALL 2”, then press the ENTER button. • The LCD’s back light flashes during the resetting operation, and when the operation is completed, “OK”is displayed and the set returns to the normal operating mode. (4) Resetting the punch through setting Press the power ON/SOURCE button and the OFF button at the same time. •“PRE”appears on the remote control unit’s display. 1 DVD Use the • and . cursor buttons to display “RST”on the remote control unit, then press the ENTER button. 2, 3, 4 3 3 Use the • and . cursor buttons to dis...