Prior to re-assembly, make certain that joining surfaces of enclosure is free of dirt. Tighten all cover bolts completely. To provide the specified protection in hazardous locations, please note that no compound of any type is to be applied on machined flange. INSTALLATION OF MATCHING TRANSFORMER Atlas Sound Model T-18, 60 Watt line matching transformer is listed by UL and C.S.A. for installation within the explosion-proof driver enclosure. Primary Winding: 2000/1000/500/250/125/85/ (45 Ohms)

Specifications subject to change without notice 1601 JACK MCKAY BLVD. / ENNIS, TEXAS 75119 U.S.A. TELEPHONE: (800) 876-3333 / FAX (800) 765-3435 AtlasSound.com © 2006 Atlas Sound Printed in U.S.A. 000706 ATS001458 RevC 7/06 SL10-2026 C A G F 19.85 Specifications subject to change without notice © 2006 Atlas Sound Printed in U.S.A. 000706 ATS001458 RevC 7/06 SL10-2026 17 TEN 1601 JACK MCKAY BLVD. / ENNIS, TEXAS 75119 U.S.A. TELEPHONE: (800) 876-3333 / FAX (800) 765-3435 AtlasSound.com A E C 19.85

The transformer is mounted on the surface with a protective shell. Model PsR-212 is larger than Model PSR-206 (see specifications). MODEL PSR-206 PSR-212 INPUT POWER 117VAC, 60 cycles, 12W 117VAC, 60 cycles, 24W OUTPUT POWER 24VDC, 500mA 24VDC, 1 amp RELAYS (NUMBER) 6 12 RELAY TYPE 24VDC,DPDT 24VDC, DPDT RELAY COIL CURRENT Nominal 35mA Nominal 35mA RELAY CONTACT RATING TERMINAL STRIPS 3 amps one point, screw type two 8 point, screw type 3 amps one 10 point, screw type three 8 point, screw

for installation within the explosion-proof driver enclosure. Primary Winding: 2000/1000/500/250/125/85/ (45 Ohms) Secondary Winding: 4, 8 & 16 Ohms Insertion loss: Less than 12dB at 1 kHz Termination: Solder Lugs Shipping Weight: 1.5 Lbs. Within the explosion-proof housing, on the back side of the magnetic assembly of the drive unit, two holes are pre-drilled for fastening the T-18 line matching transformer with 8-32 screws. When used with the Atlas Sound HLE-Series speakers, the 16 Ohm

3 Introduction, Features, and Applications ...................................................................................................................... 4 Safety Precautions ....................................................................................................................................................... 4 Front Panel Description............................................................................................................................................

Prior to using any Atlas Sound module please read the AA120M manual prior to use. It is very important for one to know the difference between Amp Direct and Mix Bus modes. KEY FEATURES 1. Gain Trim – When the gain is set to max (Clockwise), it is designed that the 70v output will not exceed 30v. When fully attenuated the module will have a 1v or less at the 70v outputs 2. EQ Trim– The EQ filter operating range is between 1 KHz and 8 kHz with a slope of 6db per octave. When the potentiometer is r

• TELEPHONE: (800) 876-3333 • FAX: (800) 765-3435 ©2006 ATLAS SOUND LP Printed in China 00606 AT000384 RevB 06/06 PN 484004 Specifications are subject to change without notice AtlasSound.com 1601 JACK MCKAY BOULEVARD ENNIS, TEXAS 75119 U.S.A. • TELEPHONE: (800) 876-3333 • FAX: (800) 765-3435 ©2006 ATLAS SOUND LP Printed in China 00606 AT000384 RevB 06/06 PN 484004 OWNER'S MANUAL MVXA SERIES MULTI-AMPLIFIED MONITOR PANEL 2 Enhanced benefits include: • Compact electronic design achieves 8 or 16 ch

The hat sections include a rack rail slot along with holes spaced the entire length of the hat section to allow for easy, secure positioning of the rack rails. This newly designed hat section is also spaced in the cabinet to allow the installation of standard 19" blank panels vertically inside the cabinet. This is perfect for "stick-on" type accessories like Atlas Sound DC power supplies & relays. Hat sections also feature slotted cut-outs for clean, organized wire management. For optimum wire m

. ATS002102 RevD 2/08 PP CP400 & CP700 COMMERCIAL OWNER'S MANUAL POWER AMPLIFIER 7 Input Wiring Balanced Inputs Balanced input wiring requires two conductors with shield (22-gauge is the most common). The use of crimp type spade lugs is highly recommended for permanent installations. At the input section located on the rear of the amplifier, wire the “hot”/positive lead to the “+” terminal, the “common”/negative lead to the “-” terminal and the shield/drain to the “ground” terminal (Figure 3). T

Remote turn on is easily accomplished by either audio or AC trigger sensors. If focused power is required a optional Hi-pass filter is incorporated. Master remote level control is easily done via an external 10k poteneometer and a line out makes easily to daisy chain amplifiers. The PA1001G can be used for many in many ways ranging from boardroom, restaurant, commercial paging and back ground music applications. 2 1 3 5 6 7 4 Front Panel 1. Power Switch This switch turns the AC Mains power to th