valutazioni - 3, GPA: 3.7 ( )

Produttore : Vermont Casting File Size : 1.41 mb File Nome : Lingua di insegnamento:

2.Feedthedoorhandleintotheholethroughthefrontofthedoorpanel. 3.Fromthebacksideofthedoorpanel, insertthemountingbracketovertheendofthehandleasshown. 4.Withlockwashersplacedonthebolts, inserttheboltsthroughthemountingplate, intothepre-threadedmountsandfirmlytightenthebolts. 141324 Assembly Step 10 Locatetheseparts: NameplatewithHeatIndicator2PushNutsHARDWAREBAGF No tools are required for this step. 1. Insert the name plate mounts and heat indicator prong through the mounting holes in the front of the 15doorpanel. 2.Fromtheinsideofthedoorpanel,securelyattachthepushnutstothenameplatemounts. Assembly Step 11 Locate these parts: Zip Tie HARDWARE BAG G S-Hook Tools needed: Pliers Using the zip tie, secure the hose to the front leg as shown. Do not pull the zip tie tight -leave it just loose enough so that the hose can be adjusted if needed. Tying the hose to the leg helps prevent the hose from coming into contact with the hot burner chamber. Inspect the installation underneath the smoker to ensure that the hose is not rubbing any portion of the burner chamber. 1. Place one end of the S-Hook around the regulator neck or hose as shown. 2. Using a set of pliers, crimp the S-Hook securely to the HVR so that it can not be removed Crimp from the HVR. 3. When an LP tank is not OR attached to the smoker, use the S-Hook to hang the HVR from the carry handle on the side of the smoker. This will help prevent dirt and other particles from plugging the end of the HVR. Assembly is now complete! Please follow all instructions and safeguards on the following pages for connecting the LP tank. 16 Connecting the LP Tank ALL INSTRUCTIONS AND SAFEGUARDS ON THIS PAGE MUST BE FOLLOWED TO PREVENT FIRE, DAMAGE, AND / OR INJURY. 1. The knob on the LP tank must be closed. See that the knob is turned clockwise to a full stop. 2. Check that the control knob on the smoker is turned off. 3. Remove the protective cap from the LP tank valve and coupling nut, if present. 4. Hold the regulator in one hand and insert the nipple into the valve outlet. Be sure the nipple is centered in the valve outlet. The coupling nut connects to the large outside threads on the valve outlet. Use care -do not cross thread the connection. 5. Hand tighten the coupling nut clockwise until it comes to a full stop. Firmly tighten by hand only. Do not use tools. CAUTION: In the connection process, the HVR side of the connection will seal on the back check in the valve, resulting in a slight resistance. The connection requires about one-half to three-quarters additional turn to complete the connection. Any fuel supply cylinder used must be constructed and marked in accordance with specifications for propane cylinders of the U.S. Department of Transportation (DOT) CFR 49, or CAN/CSA B339. The appliances is to be used only with the 20 pound, vertical standing vapor withdrawal type tank. (A) Do not store tanks under or near the smoker. (B) Never fill tanks more than 80% full. If instructions A and B above are not followed exactly, a fire causing death or serious injury may occur. This smoker is designed to operate on LP (Liquefied Propane) gas only. The 20 lb LP cylinder used with this smoker must conform to the following requirements. Diameter-12” (30.5cm) Height 18” (45.7cm) With a maximum capacity of 20 pounds The gas cylinder used must include a collar to protect the cylinder valve. The cylinder supply system must be arran...

Scarica la tua

Per scaricare, digitare 2 cifre :