valutazioni - 3, GPA: 3.3 ( )

Produttore : McCulloch File Size : 742.4 kb File Nome : Lingua di insegnamento:

IMPORTANT: WHEN UNPACKING AND AS SEM BLING TILLER, BE CAREFUL NOT TO STRETCH OR KINK CABLE(S). • Cut cable ties securing handle column. •. Route cable(s) as shown and slide handle column onto handle mount. • Remove all packing from carton. • Secure handle column using two (2) carriage bolts and two (2) flange locknuts. Tighten se cure ly. • Cut away carton. • Route tine control cable(s) through plas tic cable clip on handle mount. NOTE: Cables must not touch the muffler. • Cut cable ties securing tiller to skid. Re move tiller from skid by pulling backwards. • Remove screws securing depth stake to skid and discard the screws. depth_stake_4 DEPTH STAKE SUPPORT BOLT HEX BOLTS, LOCK WASH ERS, AND HEX NUTS DEPTH STAKE SUPPORT NUT “A” ENGINE BRACK ET HALVES Fig. 3 STAKE SPRING ASSEMBLY HANDLE HEIGHT • Handle height may be adjusted to better suit operator. (See “HANDLE HEIGHT” in the Service and Ad just - ments section of this manual). TILLING WIDTH • Tilling width may be adjusted to better handle your tilling con di tions (See “TINE ARRANGEMENT” in the Service and Adjustments section of this manual). TINE OPERATION • Check tine operation before first use. (See “TINE OPERATION CHECK” in the Service and Adjustments section of this manual). INSTALL DEPTH STAKE AS SEM BLY (See Fig. 3) • Loosen nut “A”. • Insert stake support between engine brack et halves with stake spring down. • Bolt stake support to engine brackets with bolts, lock washers and nuts. Tight en se curely. Tighten nut “A”. • Depth stake must move freely. If it does not, loosen support bolt. Fig. 2 TILLER HANDLES CABLE(S) HANDLE PANEL BOLTS 6 KNOW YOUR TILLER READ THIS MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER. Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your Tiller or in literature supplied with the product. Learn and understand their meaning. Fig. 4 MEETS ANSI SAFETY REQUIREMENTS Our tillers conform to the safety standards of the American National Standards Institute. OPERATION CHOKE CONTROL - Used when start ing a cold engine. DEPTH STAKE - Controls forward speed and the depth at which tiller will dig. ENGINE ON/OFF SWITCH - The engine switch enables and disables the ignition system. FORWARD TINE CONTROL - En gag es tines in forward direction. FUEL VALVE - The fuel valve opens and closes the passage between the fuel tank and the carburetor. RECOIL STARTER HANDLE - Used to start the engine. THROTTLE CONTROL - Used to con trol en gine speed. On/Off Switch Fuel Valve Recoil Starter Handle Forward Tine Control Depth Stake Throttle Control Choke Control Tines Fuel Fill Port 7 TINE OPERATION (See Fig. 6) FORWARD • Squeeze forward tine control to handle. HOW TO USE YOUR TILLER Know how to operate all controls before adding fuel and oil or attempting to start engine. The operation of any tiller can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your tiller and while tilling. We recommend a wide vision safety mask for over spectacles or standard safety glasses. TILLING The speed and depth of tilling is regulated by the position of the depth stake and wheel height. The depth stake should always be below the wheels for digging. It serves as a brake to slow the tiller’s forward motion to enable the tines to penetrate the ground. Also, the more the depth stake is lowered into the ground the deeper the tines will dig. DEPTH STAKE (See Fig. 6) Adjust depth stake by removing the hairpin clip and clevis pin. Change depth stake to desired position. Replace the clevis pin and hairpin clip. • For normal tilling, set depth stake at the second or third hole from the top. WHEELS (See Fig. 6) Adjust wheels by removing the hairpin clip and clevis pin. Change wheel position. Replace the hairpin clip and clevis pin. • For normal tilling, set wheels at the second or third hole from the top. depth_stake_4 DEPTH STAKE STAKE SPRING HAIRPIN CLIP AND CLEVIS PIN WHEEL Fig. 6 OPERATION Fig. 5 STOPPING (See Fig. 5) TINES 1. Release tine control to stop move ment. ENGINE 2. Move throttle control to “SLOW” po si tion and allow the engine to run slowly for cool down. 3. Turn the engine switch to the "OFF" Position. 4. Turn the fuel valve lever to the "OFF" Position. NOTE: NEVER USE CHOKE TO STOP ENGINE. IMPORTANT: TO STOP ENGINE IN AN EMERGENCY, TURN THE ENGINE SWITCH TO THE OFF POSITION. Tine Control “Off” (UP) Po si tion Tine Control “On” (DOWN) Po si tion 1 Throttle Control Engine Switch Fuel Valve Throttle Control Fuel Valve Engine Switch OPERATION TO TRANSPORT CAUTION: Before lifting or trans port ing, allow tiller engine and muffler to cool. Disconnect spark plug wire. Drain gasoline from fuel tank. AROUND THE YARD • Tip depth stake forward until it is held by the stake spring. • Push tiller handles down, raising tines off the grou...

Scarica la tua

Per scaricare, digitare 2 cifre :