valutazioni - 2, GPA: 3
(
)
)
|
Facilità d'uso
It may also be used your Operator’s Manual: The SAFETY ALERT SYMBOL indicates that there is a potential hazard to personal safety involved and extra safety precautions must be taken. When you see this symbol, be alert and carefully read the message that follows it. In addition to design and configuration of equipment; hazard control and accident prevention are dependent upon the awareness, concern, prudence and proper training of personnel involved in the operation, transport, maintenance and storage of equipment. Never operate the cutter near people and do not stand near ! DANGER! the cutter while blades are in motion. Indicates an imminently hazardous situation which, if not After striking an object, disengage PTO, shut off tractor and avoided, will result in death or serious injury. This signal word inspect for damage before continuing. is limited to the most extreme situations. Do not operate the cutter in reverse unless necessary. De bris may be thrown from the front of the cutter; therefore, increasing the risk of injury to the operator. Check the cutter periodically for loose hardware and tighten ! WARNING! Indicates a potentially hazardous situation which, if not avoid- Never operate the cutter while in the raised transport posi ed, could result in death or serious injury. Disengage the PTO when raised for transport or backing ! CAUTION! Travel slowly over rough terrain and be alert to holes and to alert against unsafe practices Safety Rules These rules and instructions must be reviewed at least annually by all operators! Most accidents are the result of negligence and carelessness, caused by failure of the operator to follow safety precautions. Even though your implement is designed with many built-in safety features, the following precautions are mandatory to prevent such accidents. Make sure everyone that uses this machine has read the Operator’s Manual and understands how to operate it safely. 1. Do not allow anyone to operate this machine who has not been properly trained in its safe operation. 2. Wear proper eye protection to prevent injury from flying objects. 3. To prevent personal injury caused by thrown objects, the use of front safety shields is strongly recommended. 4. Do not let children operate the implement. 5. Never allow passengers. Do not leave the tractor or the implement unattended with the engine running. Before cutting, clear the area of objects and debris that could become entangled in the blades or thrown from the Use warning flags or approved warning lights at night and during other periods of poor visibility. Do your best to prevent highway accidents. 9. Be alert to traffic when crossing or cutting near roadways. Always maintain complete control of the machine. Know your state and local laws concerning highway safety and regulations. Comply with these laws when transporting machinery. 10.Keep PTO shielding in place and in good condition. Do not operate cutter with shields missing. 11.Always use proper PTO speed or machine damage may result. This cutter is designed to be used with a tractor using a 540 rpm rear PTO. 12.In order to maintain steering control, add ballast to tractor. To determine the amount of ballast required refer to your tractor operator’s manual. During Maintenance 1. Before performing maintenance, disconnect PTO driveline and securely block cutter on safe supporting stands. Do not position stands under axle or wheel supports. 9/25/08 RC15, RC25, and RC35 Series Rotary Cutter 312-298M 1 2 Important Safety Information RC15, RC25, and RC35 Series Rotary Cutter 312-298M 9/25/08 Table of Contents Land Pride Safety Labels Your implement comes equipped with all safety labels in place. They were designed to help you safely operate your implement. 1. Read and follow label directions. 2. Keep all safety labels clean and legible. 3. Replace all damaged or missing labels. 4. Some new equipment installed during repair require safety labels to be affixed to the replaced component as specified by the manufacturer. When ordering new components make sure the correct safety labels are included in the request. To order new labels go to your Land Pride dealer. 5. Refer to this section for proper label placement. To install new labels: a. Clean the area the label is to be placed. b. Peel backing from label. Press firmly on surface being careful not to cause air bubbles under label. 818-130C Caution 540 RPM 14217 14217 818-161C Caution Rotary Cutter General Safety 818-130C Caution 540 RPM 14493 Model RC15 & RC25 Model RC35 Model RC15 & RC25 3 Important Safety Information 9/25/08 RC15, RC25, and RC35 Series Rotary Cutter 312-298M Land Pride Table of Contents 14218 818-161C Caution Rotary Cutter General Safety 14493 Model RC35 14242 818-187C Model RC25 & RC35 Danger PTO Shield Model RC15 14239 818-187C Danger PTO Shield 818-229C Amber Reflector 4 Important Safety Information RC15, RC25, and RC35 Series Rotary Cutter 312-298M 9/25/08 Table of Contents Land Pride 13042 ROTATING DRI...
Questo manuale è adatto anche per i modelli :Prodotti per il Giardino - RC15 Series (5.46 mb)
Prodotti per il Giardino - RC25 Series (5.46 mb)