valutazioni - 2, GPA: 4.5 ( )

Produttore : Stiga File Size : 414.93 kb File Nome : Lingua di insegnamento:

The auxiliary wheel must be folded up during operation – Installed in the front hole. The auxiliary wheel must be down for transport – Installed in the rear hole. The auxiliary wheel is folded up and down as follows: 1. Pull out the locking pin (6:T). 2. Pull out the auxiliary wheel and stay and reinstall in the desired position. 3. Reinstall the locking pin. 4.12Gearbox (1:M) The gearbox becomes extremely hot during operation. Risk of burn injuries. 4.13Rotors (1:N) Nobody must be close to the dangerous rotors during operation. The rotors are made of special steel and work the soil at the same time as the machine is propelledforwards. The machine can be operated with one, two or three rotors on each side. Removal and installation of the rotors is by removing the locking pins and screws. See fig. 8. 4.14Cutting disc (1:O). Nobody must be close to the dangerous cutting discs during operation. The cutting discs are on respective rotoraxles and are designed to border the working areaand facilitate control of the machine. 4.15 Choke The choke must never be activated during operation. This will damage the engine. The choke must be activated at cold starts. The choke is shown according to the table below: Machine Figure:Position 75-G 2:P 75R-B 1:P 75R-H 3:P 75R-HX 4:P 4.16Fuel cock The fuel cock should be open during operation and closed when the machine is not used. The fuel cock is shown according to the table below: Machine Figure:Position 75-G 2:Q 75R-B 1:Q 75R-H 3:Q 75R-HX 4:Q 4.17 Starting handle Handle for starting the engine. The starting handle is shown according to the table below: Machine Figure:Position 75-G 2:R 75R-B 1:R 75R-H 3:R 75R-HX 4:R 4.18Depth skid (1:S) The task of the depth skid is to keep the machine stable so that the soil can be cultivated. The depth skid has three positions. Shifting takes place as follows: 1. Pull out the locking pin (6:T). 2. Pull out the depth skid and reinstall in the desired position. 3. Reinstall the locking pin. ENGLISH GB ENGLISH GB The different operating properties are shown according to the table below: Holes Properties Left The machine works itself forward , angled to the left. Middle The machine works itself forward without being angled to either side. Right The machine works itself forward, angled to the right. 5 OPERATION 5.1 Fuel Read and understand all safety instructions. No fires or smoking near to petrol. Use 92-95 octane lead free petrol. Oil-mixed petrol designed for 2-stroke engines must never be used. Filling Read and understand all safety instructions. If the engine has been running, wait a few minutes until it has cooled before filling up. Fill carefully to prevent the spillage of fuel. Move the rotary cultivator at least 3 metres from the filling site before starting. Fill as follows: 1. Clean around the fuel cap. 2. Unscrew the filler cap. 3. Fill using a funnel or use a filler can with spout to prevent spillage. 4. Tighten the filler cap. 5. Move the rotary cultivator at least 3 metres from the place of filling before starting. Move the rotary cultivator at least 3 metres from the filling site before starting. 5.2 Engine Oil Always check the oil level before starting. Otherwise there is a risk of serious engine damage. Also see “4.9” and “4.10”. Check the oil level as follows: 1. Position the machine so that the engine is horizontal. 2. Unscrew the oil filler and check that the oil level is level with the lower part of the hole’s thread. 3. Top up the oil if necessary. Use normal engine oil SAE 10W-30. 4. Reassemble the oil filler cap. Move the rotary cultivator at least 3 metres from the filling site before starting. 5.2.1 Starting the engine from cold 1. Open the fuel cock. See “4.16”. 2. Put the choke in position “CHOKE”. See“4.15”. 3. Set the throttle (1:C) in the “START” position. 4. Hold the handle with one hand and slowly pull the starter handle with the other hand. See “4.17”. When the starter mechanism engages, quickly and forcefully pull the starter handle until the engine starts. NOTE! Do not pull the cord hard to its stop position and do not release it in the pulled out position. This damages the starter mechanism. 5. Reset the choke after 3-5 seconds. 5.2.2 Starting a warm engine Start a hot engine according to points 1, 3 and 4 above. The choke must not be used. 5.3 Operating The gearbox (1:M) becomes very hot during operation. Risk of burn injuries. 1. Tip the rotary cultivator back slightly so that the rotor is above ground. 2. Activate the drive control (1:B). 3. Tilt the cultivator forward so that it works its way into the soil. 4. To reverse, activate reverse control (1:A). 5.4 Stop 1. Stop the rotary cultivator by setting the throttleand stop control (1:C) to “STOP”. 2. Shut off the fuel cock. See “4.16”. 5.5 Operating tips The rotors propel the machine forward. The speed of the rotors is controlled by the throttle (1:A). Keep hands and feet away from rotatingparts (1:N). ENGLISHGB ENGLISHGB The optimum working depth vari...

Scarica la tua

Per scaricare, digitare 2 cifre :