valutazioni - , GPA: ( )

Istruzioni per l'uso Husqvarna, Modello 953900445

Produttore : Husqvarna
File Size : 1.09 mb
File Nome :

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

The characteristics of the mixture tend to deteriorate in time, so you should only prepare as much mixture as you are going to need (the use of deteriorated fuel can seriously damage the engine). Filling the tank 14 15 Clean the area around the fuel cap before removing it, to prevent any impurities from contaminating the fuel. Take the cap off the fuel container carefully. Unscrew the cap on the fuel tank and fill it with the necessary quality, using a funnel. During use, to prevent problems in starting the engine again, we strongly recommend that you avoid letting the fuel run out in the tank. Fuel storage 14 15 Store the fuel in a cool, well-ventilated place, in an approved fuel storage container. Never store the engine with fuel in the tank in a poorly ventilated place where the fumes produced by the gasoline could propagate and reach a fire, candle, burner or furnace pilot light, water heater, dryer, etc. Never store excessive quantities of fuel. E. Assembly/disassembly E1. Delta grip For your safety the label placed on the shaft at a distance of at least 11 cm fr be fastened in a comfortable working position. The safety pole guar the accessories supplied and in the configura- tion shown in the figur handle. E2. Double Handle Adjust and secur ing the scr E3. Assembly of safety guar Fit the safety guar position the lower clamp ( the shield and the upper clamp ( Insert and tighten the screws (H). . steps: Safety guard extension (exclusively for use with nylon string head) • The extension (B) should be installed only for use with the nylon string head, with the aid of the string cutter blade (L), that regulates the length of the string and thus the cutting diame• For correct assembly see the illustration on the cover and perform the following sequence of • Insert the extension (B) on the safety guard (A) at the reference notches (C), and fasten with the screws (D), then apply the string cutter blade (L) with the cutting edge facing towards the outside of the shield, and fasten it with the screw (E) (Make sure the screws are tightened all the way (E) and are not loosened by the vibrations. If necessary, tighten them again). CAUTION! If you are using the grass cutting blade, remove the extension (B) on the guard (A). ENGLISH - 5 E4. Assembly/disassembly of line cutter head Apply the nylon string head as shown in the illus- tration: 1) Upper plate 2) Protection (not supplied with all models) 3)Nylon string head. Tighten by ing counterclockwise. As you tighten, hold the nylon string head and plate still and insert theench or screwdriver supplied in the holes in the plate and gearbox; first turn the plate until the two holes match. E5. Assembly/disassembly of grass cutterblade plate e) Fixed cup f) Blade fastening nut. ing and direction arrow facing upward d) Lower (not supplied with all models) c) Blade with word- Upper plate with blade centering b) Protection Apply the blade as shown in the illustration: a) CAUTION! Do not use the nylon string head guard extension with metal blades. 2 3 4 10 2 3 4 10 E6. Attachments fitting/removal (for split shaft models only) 1) Loosen the joint knob first, then insert attachment’s shaft into the shaft/attachment joint and make sure that the locking pin (A) is secured in one of its housings, finally lock firmly the joint knob (B). 2) To remove the attachment from the power unit: loosen the joint knob(1), push the locking pin (2) and, keeping it pressed, remove attachment’s shaft from the joint(3). 3) Every attachment manual explains through a picture in which ways each attachment can be assembled on the power unit: a configuration is forbidden if crossed, if marked with “NO” and/or the symbol ., or if it isn’t shown at all. A configuration is allowed if marked with “OK” and/or the symbol . The figure shows assembling configurations allowed for the string head/grass blade attachment (with the rules defined in the previous paragraph, it is forbidden to assemble the string head/grass blade attachment with the locking pin in both left and right housings, allowing its assembling in the upper housing only). F. Starting and stopping the engine 1 5 6 7 8 9 10 11 12 14 17 CAUTION! ound or any obstacles. Start the brush cutter in a flat place. During startup stand in a stable position. Make sure the blade or nylon string head do not touch the CAUTION! Grip the knob of the starter with one hand and hold the machine in a stable position with the other. (Take care not to wind the starter string around your hand) and pull slowly until you encounter some resistance, then pull the cord sharply and forcefully (to start the engine when Do not pull the star...