valutazioni - 4, GPA: 4.3
(
)
)
|
Facilità d'uso
Release the switch trigger to stop. CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. ASSEMBLY 1. Lock-off lever 2. Switch trigger 1 2 3 1 2 3 Bolt 2. Flange 3. Diamond wheel 003526 Installing or removing diamond wheel To install the wheel, first loosen the bolt with the hex wrench and remove the bolt and the flange. Then mount the wheel, the flange and the bolt. The wheel should be mounted with the Makita name on the flange side. 1 2 1. Hex wrench 2. Blade stopper pin 003527 Press the blade stopper pin and insert it through the hole in the wheel so that the wheel cannot revolve. Use the hex wrench to tighten the bolt securely. To remove the wheel, follow the installation procedure in reverse. CAUTION: • When installing the wheel, be sure to tighten the bolt securely. • Use only the Makita wrench to install or remove the wheel. 003533 Hex wrench storage When not in use, store the hex wrench as shown in the figure to keep it from being lost. 1 1. Hex wrench 003538 003538 Attach the tank holder on the tank. The tank holder should be attached around the portion shown with the dotted line. Tighten the screw (A) to the extent that the tank can still turn within the tank holder. 1 3 4 5 2 1. Tank holder installing portion 2. Tank 3. Screw (B) 4. Screw (A) 5. Tank holder 003539 Attach the tank holder onto the motor housing. Tighten the screw (B) securely. 1 1. Screw (B) 003541 Connect the cap on the end of the polyvinyl tube to the mouth of the tank. Turn the tank clockwise when making the connection. Then tighten the screw (A) securely to secure the tank. CAUTION: • If you find the polyvinyl tube is bent like a “V” or has been strained excessively after installing the water supply, loosen the screw (B) and adjust the position of the tank to alleviate the bent, pinched or strained condition. 003542 Water supply Remove the cap on the tank and fill through the hole. Recap the tank. Be sure that the water cock is turned off when filling the tank with water. CAUTION: • When filling the tank with water, be careful not to let the tool get wet. 1 1. Cap OPERATION OPERATION 4 Hold the tool firmly. Set the base plate on the workpiece to be cut without the wheel making any contact. Then turn the tool on and wait until the wheel attains full speed. Feed water to the wheel by adjusting the water cock to obtain a gentle flow of water. Move the tool forward over the workpiece surface, keeping it flat and advancing smoothly until the cutting is completed. Keep your cutting line straight and your speed of advance uniform. 1 1. Base For fine, clean cuts, cut slowly. (When cutting glass plate 5 mm (3/16”) thick, cut at about 250 mm/min (9-7/8”/min). When cutting tile 10 mm (3/8”) thick, cut at about 300 mm/min (11-13/16”/min).) Also slow down as you complete a cut to avoid breaking or cracking the workpiece being cut. CAUTION: • Be sure to hold the workpiece firmly down on a stable bench or table during operation. • Do not twist or force the tool in the cut, or the motor may be overloaded or the workpiece may break. • Do not use the tool with the wheel in an upward or sideways position. • When cutting glass plate, it is recommended to attach a rubber plate (optional accessory) on the base of the tool to prevent the workpiece surface from being scratched. • The wheel for this tool is a wet-type wheel for glass and tile applications. Be sure to feed water to the wheel during operation. • If the cutting action of the wheel begins to diminish, dress the cutting edge of the wheel using an old discarded coarse grit bench grinder wheel or concrete block. Dress by pressing lightly on the outer edge of the wheel. NOTE: • If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. MAINTENANCE Ni-Cd ACCESSORIES CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. After use Brush off accumulation of dust on the base. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. EN0001-1 Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. To recycle the battery: 1. Remove the battery from the tool. 2. a) Take the battery to your nearest Makita Factory Service Center or b) Take the battery to your nearest Makita Authorized Service Center or Distributor that has been designated as a Makita battery recycling location. Call your nearest Makita Service Center or Distributor to determine the location that provides Makita battery recycling. See your local Yellow Pages under “Tools-Electric”. • These accessories or attachments are recommended for use with your Makita...
Questo manuale è adatto anche per i modelli :Prodotti per il Giardino - 41900 (265.02 kb)