valutazioni - 5, GPA: 3.8
(
)
)
|
Facilità d'uso
It helps regulate the depth of the cut and also acts as a brake to help the operator control the speed of the cultivator. . Lowering the depth stake will slow the cultivator and make it till deeper. Raising the depth stake will allow it to move faster and till more shallow. . If the cultivator stops forward motion and tries to dig deeper than necessary, move the handles from side to side to start forward motion. . Cultivating is loosening or digging around growing plants which allows the plants to flourish. . When using the cultivator to remove weeds, it is best to cultivate no deeper than 1–1/2 inches. Cultivating deeper will only pull to the surface ungerminated weed seeds. Raising the depth stake will allow it to move faster and till more shallow. . When cultivating around plants or close areas, you may want to remove the outside tines. See “Tine Replacement” in the Service/Adjustments section. . For better control when cultivation around delicate plants, turn over the stake and support the cultivator with the wheels. WARNING: Read the Owner’s manual. Know location and functions of all controls. Keep all safety devices and shields in place. Never allow children or uninstructed adults to operate cultivator. Shut off engine before unclogging tines or making repairs. Keep bystanders away from machine. Keep away from rotating parts and tines. They can cause injury. HINTS FOR DEPTH STAKE OR WHEEL ADJUSTMENT Light cultivation with moderate growth (1 to 2 inches depth) Adjust the wheels upward to their highest or next to their highest position. Make sure the handles are at a comfortable height for operating the cultivator. Seed bed preparation (4 to 6 inches depth) Use the depth stake. Adjust the depth stake downward for deeper cultivation. Heavy soil (4 inch depth or greater) Remove the depth stake and work the tines down with a back and forth motion to at least a depth of 4 inches. Slowly pull the cultivator backward allowing the soil to feed forward over the tines. F–041306C 15 MAINTENANCE CUSTOMER RESPONSIBILITIES #;!#$#. * 2. , . . 7 . . . . *. . ). . <. ). . >. ). 7 . ,. 7 . . . #;!. ". Tighten All Screws and Nuts v v Lubricate Tine Shaft v v Lubricate Transmission v v Check Spark Plug v v Clean and Oil Air Cleaner Filter v v Clean Cylinder Exhaust Ports v Drain Fuel v PRODUCT SPECIFICATIONS Model No.: See Nameplate Date Of Purchase: Horse Power: 2 Displacement: 3.0 cu. in. (49.2 cc.) Gasoline Capacity: 20 oz. Fuel/Oil Mix Ratio: 24:1 Oil To Gas (5.3 oz. oil to 1 gal. gas) (use unleaded regular) Spark Plug: Champion RCJ–8Y Spark Plug Gap: 0.035 inch Idle RPM: 1700–3000 GENERAL RECOMMENDATIONS The warranty on this cultivator does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must maintain the cultivator as instructed in this manual. Some adjustments must be made periodically to properly maintain your cultivator. All adjustments in the Service and Adjustments section of this manual must be checked at least once each season. F–041306C 16 MAINTENANCE LUBRICATION Every 25 hours and/or at the beginning of each season, make sure the gear box is filled with lubricant (see Figure 12). Tubes of gear lubricant are available from most automotive supply stores. Use portable tool grease such as Lubriplate 630AA (Product No. 06787, 1–3/4 oz. tube) or Lubriplate GR–132 (Product No. 15892, 10 oz. tube). After cleaning and before storage, apply oil to the tine shaft (see Figure 12). WARNING: Allow the transmission to cool before filling with grease. 1. Remove both left side tines. See “How To Replace The Tines” in the Service and Adjustments section. 2. Remove the air vent screw (see Figure 12). 3. Mount a grease gun onto the grease fitting. Fill the transmission until the grease begins to come out of the air vent screw hole. 4. Reinstall the air vent screw. 5. Check the condition of the felt washer (see Figure 12). Replace the felt washer if it is damaged (see the Repair Parts section in this manual). 6. Clean and lubricate the tine shaft with a few drops of oil. 7. Reinstall the left side tines. 8. Remove the right side tines. Check the felt washer for damage. Clean and oil the tine shaft. Reinstall the right side tines. Figure 12 Grease Fitting Tine Shaft Air Vent Screw Felt Washer HOW TO CLEAN THE TINES Always remove dirt and debris from the cultivator after each use. Remove any string, wire or vegetation that may become lodged in the mechanism and stop the tines from rotating. 1. Release the throttle control and move the on–off switch to the OFF position. Disconnect the spark plug wire from the spark plug. 2. While wearing gloves, remove the hairpins and clevis pins that secure the tine assemblies to the shaft (see Figure 13). Remove the tines from the shaft. 3. Remove any lodged debris from the shaft and tines. Clean and lubricate the tine shaft with a few drops of oil. 4. Reassemble the tines on the shaft and secure with a...
Questo manuale è adatto anche per i modelli :Prodotti per il Giardino - 11052x4NC (834.08 kb)