valutazioni - , GPA: ( )

Istruzioni per l'uso Paladin Tools, Modello LAF3438

Produttore : Paladin Tools
File Size : 631.4 kb
File Nome : 160fff57-8d98-4bb5-9db1-85785841a8ed.pdf

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

2. Carefully raise the loader arm and cycle the tilt cylinders to check hose clearances and to check for any interference. WARNING Do not lock the auxiliary hydraulics of your tractor or power unit in the “ON” position. Failure to obey this warning could result in death or serious injury. 7 ROTO-TILLER OPERATION SAFETY FIRST!! READ AND UNDERSTAND THE SAFETY INSTRUCTIONS (pages 2-5 of this manual) BEFORE BEGINNING ANY ROTO-TILLER OPERATION WARNING Failure to obey the following procedures could result in death or serious injury. .. Never lift the lowest portion of this product higher than 1’-0” above the ground while operating. .. Do not lock the auxiliary hydraulics of your power unit in the “ON” position. .. Keep everyone at least nine feet away from the unit when operating. .. This product may be operated while moving forward or backward with your power unit. .. The auxiliary hydraulics must be engaged so that: .. the tines rotate down into the untilled area in the direction of travel to achieve the fastest tilling speeds and the most efficient use of power or .. the tines rotate up from under the untilled area in the direction of travel to achieve greatest conditioning of the soil. IMPORTANT Tilling while moving forward with the hinged shroud panel fully down CAN result in damage to this product and WILL void all FFC Attachments warranties. .. When tilling while moving forward, the hinged shroud panel must be chained up in a horizontal position to avoid damaging the panel. The hinged shroud panel is not designed to push any soil or other materials. .. Your power unit should be operating at full throttle with the auxiliary hydraulics fully engaged. The speed of the movement of your power unit should be varied as required to pulverize the soil to extent desired. .. The maximum tilling depth is 6”. This depth is attained when the motor guard is about 1” below the surface of the soil. Compacted soils may require two passes to reach this depth. IMPORTANT Attempting to grind stumps or dig into rigid or frozen materials CAN result in damage to this product and WILL void all FFC Attachments warranties. ROTO-TILLER MAINTENANCE SAFETY FIRST!! READ AND UNDERSTAND THE SAFETY INSTRUCTIONS (pages 2-5 of this manual) BEFORE BEGINNING ANY ROTO-TILLER MAINTENANCE BEFORE EACH USE .. Make sure that all nuts and bolts are in place and properly tightened. .. Make sure that all other fasteners are in place and are performing their specified function. .. Make sure that all hydraulic fittings are tightened and that there are no leaks in any fittings or hoses. .. Make sure that all safety signs are in place, are clean, and are legible. (SEE THE SAFETY SIGN SECTION ON PAGE 5.) .. Replace any damaged parts and excessively worn parts. AFTER EVERY 10 HOURS OF USE .. Oil the hinge at the top of the hinged shroud panel. AFTER EVERY 40 HOURS OF USE .. Make sure the taper lock adapter assemblies are tight by turning the bearing locknut by hand. If the bearing locknut moves by hand, retighten the taper lock adapter assembly as specified in Roto-tiller Service (on page 8). 8 ROTO-TILLER SERVICE SAFETY FIRST!! READ AND UNDERSTAND THE SAFETY INSTRUCTIONS (pages 2-5 of this manual) BEFORE BEGINNING ANY ROTO-TILLER SERVICE Removing Wire, Twine, Weeds, etc. that are Wrapped Around the Roller 1. Park your power unit on a level surface with this product properly attached. 2. Place your power unit’s transmission in “Park” and engage the parking brake. 3. Lower this product onto preplaced blocking that will support the motor guards of this product so that the tines are not in contact with the ground. WARNING Failure to obey the following procedures could result in death or serious injury. .. Do not use blocking made of concrete blocks, logs, buckets, barrels or any other material that could suddenly collapse or shift positions. Do not use wood or steel blocking that shows any signs of material decay. Do not use blocking that is warped, twisted, or tapered. 4. Shut off your power unit’s engine, remove the starter key, wait for all moving parts to come to a stop, and relieve all pressure in the hydraulic lines. 5. Disconnect the hydraulic lines from your power unit and connect the two ends to each other. This should permit the tines to rotate freely. 6. Pull the material from the tine shaft while allowing the shaft to rotate. ALTERNATE METHOD If your power unit is equipped with safety stops for the lift arms of the loader that can be activated from the operator’s position or if the safety stops must be activated from outside the operator’s position and a second person is present, then Step 3 above may be replaced with these steps: a) Fully raise the lift arms and fully extend the tilt cylinders to the fully dumped position. b) Activate the safety stops for the lift arms. Test the stops to verify that no downward movement of the lift arms can occur. c) Continue with Step 4 above. Replacing Tines 1. Perform steps 1 through 5 above. 2. Remove the clip a...