Produttore : Troy-Bilt
File Size : 2.15 mb
File Nome : b79b45fc-475e-2424-01f9-dbd2c92091f9.pdf
|
Facilità d'uso
5. Place the clamps and J-handle the over the shaft housing and onto the bottom clamp. 6. Hold each hex nut in the bottom clamp recess with a finger. Start screws with a large Phillips screwdriver. Do not tighten until you make the handle adjustment. Decal Adjusting 7. Loosen the screws so that the J-handle can be easily moved in the clamp assembly. Do not remove the screws or nuts. 8. Slide the J-handle in or out until the arrow/white line on the decal touches the clamp assembly (Fig. 2). 9. While holding the unit in the operating position (Fig. 3), maneuver the J-handle to the location that provides you the best grip. 10. Tighten the clamp screws evenly, until the J-handle is secure. NOTE: Once the new J-handle is installed, there is no need to change back to the original handle when you are done using the attachment. Keep this new handle installed when you use your original unit as a string head trimmer. Fig. 2 IDENTIFY & REMOVE YOUR ASSIST HANDLE Your trimmer is configured with one of many types of assist handles. You must remove the current assist handle and install the 24” J-handle (included) in order to use the TBBC attachment. Consult your trimmer’s manual to determine what type of handle you have. Follow the instructions outlined in the manual in order to remove the current handle and its clamps, screws, nuts, bolts or other hardware. NOTE: Your trimmer may be equipped with a small J–handle. This small handle is NOT an acceptable substitute for the larger J-handle that is included with the TBBC. Remove the smaller J-handle so you can install the larger, 24-inch handle. Before you can use the TBBC attachment, you must make some adjustments to the trimmer or trimmer/ brushcutter that you are attaching the TBBC to. You will have to: • Remove your current assist handle • Install the supplied 24” J-handle • Install the shoulder strap clip (if necessary) • Attach/adjust the shoulder strap These instructions are explained on the next couple pages. To comply with safety regulations, you MUST use the large 24” J-handle that is included with the attachment when operating the TBBC. The handle is required as a barrier bar to the brush blade. WARNING: Shaft Grip Fig. 1 Fig. 3 ASSEMBLY INSTRUCTIONS INSTALL THE SHOULDER HARNESS LOOP When operating the brushcutter attachment, you must use the shoulder harness that is provided with the unit. Check to see if your trimmer has a wire form support fitting that you can clip the strap to. If your unit has the fitting that is shown in Figure 4, you do not need to install the harness loop provided. If so, head to the next section Install the Harness. Wire Form Support Fitting Fig. 4 If your trimmer does not have an existing wire form fitting, you must install the clip that is included with the TBBC. To install the supplied shoulder harness clip: 1. Remove the bolt, nut and washer that were installed on the harness loop for shipping. Keep them handy. 2. Pull the clamp open and push it onto the boom. 3. Arrange the clip so that it is close to the shaft grip and away from the J-handle (Fig. 5). 4. Insert the bolt through the clip and secure it with the washer and nut, using a pair of pliers and a small crescent wrench. Securing Nut Boom J-handle Shaft Grip Fig. 5 INSTALL THE SHOULDER HARNESS Always use theWARNING: shoulder harness when using the cutting blade to avoid serious personal injury. 1. Push the strap through the center of the buckle. 2. Pull the strap over the cross bar and down through the slot in the buckle (Fig. 6). 3. Put the harness on over head and onto the left shoulder. Snap it on to the support fitting (Fig. 7). 4. Adjust length to fit the operator’s size. Pull tab to lengthen, pull strap to shorten (Fig 8). Fig. 6 Fig. 7 Fig. 8 OPERATING INSTRUCTIONS Never use this attachment with an electric-powered unit. Only attach the TBBC to gas-powered trimmers or brushcutters. Use with an electric product could lead to damage to the unit or serious personal injury. WARNING: OPERATING THE EZ-LINK™ SYSTEM The following attachments are also available: Cultivator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TBGC Edger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TBLE Hedge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . .TBAH Straight Shaft Trimmer . . . . . . . . . . . . . . . . . . . . . . TBSS Turbo Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TBTB Pole Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TBPS When using any attachment, read and understand that attachment’s specific manual before you begin operation. Follow all applicable safety information. WARNING: To avoid serious personal injury and damage to the unit, shut the unit off before removing or installing add-ons. WARNING: Removing the Add-On 1. Turn the knob counterclockwise to loosen (Fig. 9). 2. Press and hold the release button (Fig. 9). 3. While firmly holding the upper shaft housing, pull the add-on straight ou...