valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
The length of the shield must be aligned with the length of the shaft. 1. Place the metal shield under the gearbox, and align the screw holes. ShieldGearbox 2. Insert and thread the 4 mounting screws through the holes of the gearbox and the metal shield. Tighten evenly and securely with the hex wrench provided. INSTALLATION OF THE METAL BLADE WARNING: Wear protective gloves when handling or performing maintenance on the blade to avoid injury. The blade is sharp and can cut you even when it is not moving. WARNING: Do not use any blades, or fastening hardware other than the washers and nuts shown in the following illustrations. These parts must be provided by Poulan/Weed Eater and installed as shown below. Failure to use proper parts can cause the blade to fly off and seriously hurt you or others. NOTE: The dust cup and retaining washer are located on the gearbox shaft and not in the parts bag. All other fasteners mentioned in the following assembly steps are in the parts bag. 1. Remove the retaining washer from the threaded shaft of the gearbox. Leave the dust cup on the shaft. 2. Install the blade and the retaining washer over the threaded shaft. 3. Make sure the raised part of the retaining washer is facing the gearbox and the raised area fits into the hole in the center of the blade. 4. Slide the blade and retaining washer onto the shaft of the gearbox. 5. Place the cupped washer onto the shaft. Make sure the cupped side of the washer is toward the blade. 6. Install the blade nut by threading onto the shaft counterclockwise. ShieldBladeRetainingWasherDustCupCuppedWasherNutThreadedShaftGearbox NOTE: Make sure all parts are in place as illustrated, and the blade is sandwiched between the dust cup and the retaining washer. There should be no space between the blade and the dust cup or the retaining washer. 7. Align hole in dust cup with hole in side of gearbox by rotating the blade. 7 8. Insert a small screwdriver into aligned 9. Tighten blade nut firmly with a wrench holes. This will keep the shaft from turn-while holding screwdriver in position. ing while tightening the blade nut. 10. Remove the screwdriver. 11. Turn blade by hand. If the blade binds against the shield, or appears to be uneven, the blade is not centered, and you must reinstall. NOTE: To remove blade, insert screwdriver into aligned holes. Unthread the nut and remove parts. Be sure to store parts and instructions for future use. Screwdriver OPERATION KNOW YOUR BRUSHCUTTER ATTACHMENT READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR BRUSHCUTTER ATTACHMENT. Compare the illustrations with your unit to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. BladeShieldBladeGearboxShaftHangerTrimmerShieldTrimmerHeadBLADETheBLADEisdesignedforcuttinggrass, weeds,andbrushupto1/2inch(1cm)indiameter. TRIMMERHEADTheTRIMMERHEADholdscuttinglineandisBLADESHIELDTheBLADESHIELDprovidesprotectionfromthespinningblade. TRIMMERSHIELDTheTRIMMERSHIELDprovidesprotectionfromthespinningtrimmerline. designed for cutting grass and light weeds. OPERATING THE COUPLER Your powerhead is equipped with a coupler which enables optional attachments to be installed. The optional attachments are: MODEL: Edger ....................... PPB1000E Cultivator ................... PPB2000T Blower ...................... PPB3000B WARNING: Always disconnect powerhead spark plug before removing or installing attachments. REMOVING BRUSHCUTTER ATTACHMENT (OR OTHER OPTIONAL ATTACHMENTS) CAUTION: When removing or installing attachments, place the powerhead and attachment on a flat surface for stability. 1. Loosen the coupler by turning the knob counterclockwise. Upper Shaft 2. Press and hold the locking/release button. 8 CouplerLOOSENTIGHTENLowerAttachment Knob Locking/ReleaseButtonCouplerUpperShaftLowerAttachmentLocking/ReleaseButtonCouplerUpperShaftLowerAttachment 3. While securely holding the upper shaft, pull the attachment straight out of the coupler. INSTALLING OPTIONAL ATTACHMENTS 1. Remove the shaft cap from the attachment (if present) and discard. 2. Position locking/release button of attachment into guide recess of upper shaft coupler. Coupler Primary Hole GuideRecess Upper Locking/ Attachment Shaft Release Button 3. Push the attachment into the coupler until the locking/release button snaps into the primary hole. 4. Before using the unit, tighten the knob securely by turning clockwise. INSTALLING ATTACHMENT HANGER An attachment hanger is provided for storage when attachment is not in use. To install hanger on attachment: 1. Remove the shaft cap from the attachment (if present) and discard. 2. Press and hold the locking/release button. 3. Push hanger onto the attachment until the locking/release button snaps into the hole. OPERATING POSITION Eye Protection Heavy, Long Pants ALWAYS WEAR: Boots Cut from your left to your right. NOTE: This brushcutter attachment is not designed for use with electric powerheads. ...
Questo manuale è adatto anche per i modelli :Prodotti per il Giardino - PPB4000C (362.57 kb)