Recommended max. speed: See the Technical data section. During the running-in period (8-10 tanks of fuel) the maximum speed should be set 600-700 rpm below the recommended maximum speed (= open the high speed jet H a further 1/8 turn). Conditions • Before any adjustments are made, make sure that the air filter is clean and the air filter cover is fitted. If you adjust the carburettor when the air filter is dirty it will result in a leaner mixture when the filter is finally cleaned. This can lead

Read through the Operator‘s Manual carefully and understand the content before using the machine. Always use • A protective helmet where there is a risk of falling objects • Ear protection • Approved eye protection max 10000 rpm Max. speed of output axle, rpm This product is in accordance with applicable CE directives. Beware of thrown objects and ricochets. The operator of the machine shall ensure, while working, that no persons 15 m 15 m 50FT50FTor animals come closer than 15 metres. Blade can

Take great care when working on sloping ground. 5Keep a good balance and a firm foothold. 6Always hold the machine with both hands. Hold the machine on the right side of your body. 7Keep the cutting attachment below waist level. 8The engine must be switched off before moving. 9Never put the machine down with the engine running unless you have it in clear sight. WARNING! Neither the operator of the machine nor anyone else may attempt to remove the cut material while the engine is running or the c

The only accessories you can operate with this engine unit are the cutting attachments we recommend in the chapter on Technical data. Never use the machine if you are tired, if you have drunk alcohol, or if you are taking medication that could affect your vision, your judgement or your co-ordination. Wear personal protective equipment. See instructions under the heading Personal protective equipment. Never use a machine that has been modified in any way from its original specification. Never use

12 – English ASSEMBLY Assembling other guards and cutting equipment • Fit the guard (A) intended for use with the trimmer head. Secure using four bolts (L) and the support plate (M) as shown in the diagram. • Fit the disc drive (B) on the output axle. • Turn the blade axle until one of the disc drive’s holes aligns with the corresponding hole in the gear housing. • Insert the locking pin (C) into the hole to lock the axle. • Screw on the trimmer head (H) in the direction of rotation. • Dismantli

English – 7 SAFETY INSTRUCTIONS General safety instructions IMPORTANT INFORMATION • The machine is only designed for trimming grass. • The only accessories to be used with the engine unit as a drive source are the cutting units we recommend in the chapter “Technical data“. • Never use the machine if you are tired, if you have consumed alcohol, or if you are taking medicines that can affect your sight, your judgement or the control of your body. • Use personal protective equipment. See the sectio

• Check that the guard is not damaged or cracked. Replace the guard if it is exposed to impact or is cracked. • Check that the trimmer head and spray guard are not damaged or cracked. Replace the trimmer head or spray guard if they are exposed to impact or are cracked. • Never use the machine without a guard or spray guard nor with a defective guard. Start and stop ! ! WARNING! The complete clutch cover with shaft must be fitted before the machine is started, otherwise the clutch can become loos

• NOTE! Never use a machine without the possibility of calling for help in the event of an accident. 2.Avoid usage in unfavourable weather conditions. For example, thick fog, heavy rain, strong winds or extreme cold, etc. To work in bad weather conditions is tiring and can create dangerous circumstances, e.g. slippery surfaces, affect a tree‘s direction of fall, etc. 3.Make sure you can walk and stand safely. Look out for any obstacles with unexpected movement (roots, stones, branches, pits, dit

speed, left/right handles, min: At max. speed, left/right handles, max: GR 2026D 1,64/26,9 1,38/35 1,10/28 2 700 11 000-11 700 10 000 0,9 KW/ 9 000 rpm Yes Yes Walbro CD Champion RCJ 7Y NGK BPMR7A 0,02/0,5 Walbro WT 1,06/0,5 13,2/6,0 93/99 2,0/2,2 2,2/3,0 1,8/2,1 2,5/3,6 GR 2032D 1,88/30,8 1,38/35 1,26/32 2 700 11 000-11 700 10 000 1,1 KW/ 8 400 rpm Yes Yes Walbro CD Champion RCJ 7Y NGK BPMR7A 0,02/0,5 Walbro WT 1,06/0,5 14,3/6,5 90/100 2,5/2,5 3,0/3,5 2,0/2,0 5,1/4,9 GR 2036 2,21/36,3 1,50/38 1

Long periods at full throttle without any load on the engine can lead to serious engine damage. ! WARNING! Sometimes branches or grass get caught between the guard and cutting attachment. Always stop the engine before cleaning. WARNING! Machines fitted with saw blades or grass blades can be thrown violently to the side when the blade comes into contact with a fixed object. This is called blade thrust. A blade thrust can be violent enough to cause the machine and/or operator to be propelled in an