PLEASE CALL KOMATSU ZENOAH AMERICA INC. AT (77G)-381-5147. IMPORTANT: YOU WILL RECEIVE A WARRANTY REGISTRATION CARD AT TIME OF PURCHASE.PLEASE FILL OUT THE CARD AND SEND IT TO RedMaX 1 KOMATSU ZENOA AMERICA WITHIN SEVEN (7) DAYS.BE SURE TO KEEP A COPY FOR YOUR RECORDS. KOMATSU ZENOAH AMERICA INC. 4344 Shackleford Road Suite 500 Norcross, Georgia 30093 RedMax Garantie limitée Para LRT-A cuando se utilice un aditamento en fas unidades detalladas en ia cubierta de este manual. 90 jours à compt

Ignition switch 3. Throttle cable 4. Throttle lever 5. Throttle set button 6. Drive shaft housing 7. Debris guard 8. Cutting line head 9. Gear case 10. Spark arrester 11. Starter knob 12. Fuel tank 13. Primer pump 14. Choke lever 15. Air cleaner cover 2. Specifications ¦ BCZ2400S Overall size(LxWxH) ············································································ 71.3(1810)x9.0(228)x11.5(292) in(mm) Dry weight ··················································· 10.8 lbs (4.88kg) (11.

CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The California Air Resources Board and KOMATSU ZENOAH are pleased to explain the emission control system warranty on your 1995 and later small off-road engine. In California, new small off-road engines must be designed, built and equipped to meet the state’s stringent anti-smog standards. KOMATSU ZENOAH must warrant the emission control system on your small off-road engine for the periods of time listed below pro

Properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this product. SAVE THIS MANUAL FOR FUTURE REFERENCE Thank you for buying a Ryobi trimmer. BC30 RY30060B SS30 RY30040B CS30 RY30020B OPERATOR’S MANUAL 30cc String Trimmers and Brushcutters TABLE OF CONTENTS • Introduction ...........................................................................................

1. Coja los mangos firmemente con ambas manos. Separe los pies ligeramente (un poco mas que el ancho de sus hombros) de manera que su peso quede distribuido uniformemente en ambas piernas, y asegurese de mantener siempre una postura firme mientras trabaja. 2. Mantenga la velocidad del motor al nivel necesario para realizar el trabajo de corte, y nunca aumente la velocidad del motor por encima del nivel requerido. 3. Nunca haga funcionar la podadera a un angulo superior a 60., para reducir asi el

Liste des pieces ..................................................43 1. Posicion de las piezas ..........................................5 2. Especificaciones ...................................................5 3. Etiqueta de advertencias en la maquina...............7 4. Simbolos presentes en la maquina.......................7 5. Instrucciones de seguridad...................................9 6. Montaje ...............................................................19 7. Combustible............

(MA5) (1) spark arrester ¦ GEAR CASE (MA6) • The reduction gears are lubricated by multipurpose, lithium-based grease in the gear case. Supply new grease every 25 hours of use or more often depending on the job condition. • Remove the side bolt in gearcase opposite of grease nipple before installing new grease to arrange for old grease to exit. ¦ INTAKE AIR COOLING VENT WARNING •Never touch the cylinder, muffler, or spark plugs with your bare hands immediately after stopping the engine. The engi

WARNING IMPORTANT IMPORTANT OPT4 BCZ2600S BCZ2600SU OPT6 OPT5 OPT3 BCZ2600S BCZ2600SU .27 . .28 . 11. Optional blade usage speed is too low, or the blade cuts too deep into weeds. Adjust the engine speed and cutting depth according to the condition of object. • If the grass or other object gets caught in the blade, or if the unit starts to shake or vibrate, turn off the engine and check the whole unit. Change the blade if it has been damaged. • Turn off the engine and make sure the blade has com

seguir el reglamento de su localidad. 42 12. Optional blade usage English OPT2 (1) OPT1 Change to the debris guard which is suitable for the metal blade. (OPT1) TIGHTENING TORQUE : 26~43.5 in-lbs (2.94~4.9 N.m.) (1) Guard : T3246-24110 Change the loop handle to the J-handle for safe operation. (OPT2) (1) Bracket : 3583-14101 (2) J-handle : 6367-14200 IMPORTANT IMPORTANT OPT2 (1) OPT1 Change to the debris guard which is suitable for the metal blade. (OPT1) TIGHTENING TORQUE : 26~43.5 in-lbs (2.94

APPLICABLE SERIAL NUMBERS : 90200101 and up US-1 PSZ2450S SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. ¦ WARNINGS IN THE MANUAL WARNING This mark indicates instructions which must be followed in order to prevent accidents which could lead to s