valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
If using a check-valve, drill a 1/16” 3. hole in the discharge hose, or pipe 1” to 2” above the Base (27). The hole will prevent an air lock in the Motor (18) both at start up and/or if the Sewage Pump should lose its prime. After the check-valve, a (full-port) 4. gate-valve (not supplied), which will pass 2” solid waste should be installed in the system. The gate-valve allows removal of the Sewage Pump for cleaning and service. NOTE: If you do not feel qualified to completely (and safely) install this Sewage Pump, it is recommended that you have it installed by a qualified plumber, or service technician. Operating Instructions Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Before operating the Sewage Pump, 1. put on ANSI-approved safety goggles and other safety gear including heavy-duty, insulated rubber gloves. Safety goggles and other safety gear are sold separately. Install the Sewage Pump firmly on it’s 2. Legs and supported by rigid hose, or pipe discharge fixtures to eliminate twisting and damage from motor torque during operation. After installation, allow the Sew3. age Pump to flood with water before plugging Power Cord (1) into outlet. This will help prevent over heating from running the Motor (18) with no water resistance moving through the Sewage Pump. Once this Sewage Pump is plugged into a 120 Volt GFCI outlet, the Motor (18) will start automatically. This Sewage Pump is designed to 4. transfer waste water in cycles. Rev 09i Maintenance And Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. To prevent serious injury from accidental operation or electric shock: Unplug the Sewage Pump from its electrical outlet before performing any accessory change, inspection, maintenance, and/or cleaning procedures. To prevent serious injury from tool failure: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication BEFORE USE and PERIODICALLY 1. THEREAFTER, inspect the general condition of the Sewage Pump. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. 2. WARNING! If the supply cord of this appliance is damaged, it must be replaced only by a qualified service technician. WARNING: This Sewage Pump contains dielectric motor oil for both lubrication and heat transfer. It may be under pressure because of heat collection. Let the Sewage Pump cool for at least 2 hours before inspecting, or servicing. This oil may be dangerous to the environment. Always dispose of used oil in compliance with all local, State and Federal rules and regulations. Unclogging the Impeller (24). Unplug the Sewage Pump, put on 1. heavy-duty insulated rubber gloves and ANSI-approved safety goggles. Remove the discharge hose, or pipe.2. Lift Sewage Pump out of water using 3. the Handle (5). To unclog the Impeller (24), remove 4. 5 Screws (28) on the Sewage Pump bottom and remove Base (27). Flush the Impeller (24) with clean, 5. lukewarm water. Reinstall the Impeller (24) and re6. place the Base (27) using the 5 Screws (28). Using the Handle (5), replace the 7. Sewage Pump into water in original position. Re-thread the discharge pipe, or 8. hose. Plug the Sewage Pump back into the 9. 120 Volt, GFCI power outlet. The Sewage Pump will start auto10. matically. Troubleshooting Problem Possible Causes Likely Solutions Sewage Pump will not start. No power at outlet.1. Circuit breaker tripped.2. Cord not connected.3. Water level too low. 4. Check power at outlet.1. Check circuit breaker for outlet.2. Check that cord is plugged in.3. Check water level.4. Low flow from discharge outlets. Possible excess solid debris lodged 1. in Impeller. Check and clean debris from 1. Impeller per instructions on Page 6. Sewage Pump starts and stops too often. Possible back flow from discharge 1. pipe and/or hoses. Check-valve either not installed, or if 2. installed, it is leaking. Install a check-valve. 1. Remove and examine check-valve 2. for proper installation and operation. Replace if necessary. Sewage Pump operates but delivers little or no water. Low line voltage. 1. Debris caught in Impeller or 2. discharge hoses or pipes. Check-valve stuck closed or 3. installed backwards. If voltage is under recommended 1. minimum, check wiring size from the main switch on property. If not OK, contact local power company. Remove and check Impeller and 2. discharge hoses or pipes. Clean if needed. Remove and examine check-valve 3. and reinstall correctly or replace. Follow all safety precautions whenever diagnosing or servicing the appliance. Disconnect power supply before service. PLEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor has provided the p...