valutazioni - , GPA: ( )

Istruzioni per l'uso Axor, Modello Raindance S 27005XX1

Produttore : Axor
File Size : 5.29 mb
File Nome : hruh0136.pdf

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Install the anchors. Seal the wall around the anchors with waterproof sealant. Hold the panel against the wall. Install the gray plastic insert. Insert the top screw through the front of the panel, the washer and the insert. Screw it into the anchor. Install the center and bottom screws and washers. Connect the supply hoses to the hot and cold supply elbows. Connect the supply hoses to the hot and cold inlet ports on the valve. Turn the water on at the main. Push the diverter stem up to turn the water on to the panel. Check all connections for leaks. Once you ensure that the connections are watertight, push the diverter stem down to turn the water off to the panel. Install the side seals on the front cover. Trim off any excess. Push the front cover into place. Install the diverter sleeve. Make sure that the indexing mark on the thermostatic mixer sleeve is at the 12:00 position. Install the thermostatic mixer handle. Tighten the handle screw with a flat-bladed screwdriver. Install the diverter handle. Tighten the set screw with a 4 mm Allen wrench. Place a black rubber washer in one end of the handshower hose. Screw this end of the hose to the handshower outlet port. Place the screen washer in the other end of the hose. Screw this end of the hose to the handshower. Place the handshower in the holder. Adjust the Slider You can make the slider easier or harder to move. Use a 2.5 mm Allen wrench to turn the set screw clockwise to increase the tension, counter-clockwise to decrease the tension. Justify the Thermostatic Mixer Handle Turn the water on to the handshower. Turn the thermostatic mixer handle until the output water measures 100o on a thermometer. Turning the handle clockwise makes the water cooler, counter-clockwise makes the water warmer. Turn the water off. Loosen the thermostatic mixer handle screw. Remove the handle. Replace the handle so that the safety stop override button is at the 12:00 position. Tighten the set screw. Set the High Temperature Limit Stop (optional) Remove the thermostatic mixer handle. Remove the clip and the stop ring from the stem of the thermostatic mixer. Turn the water on to the handshower. Turn the temperature control stem until the output water is the desired maximum high temperature -- usually 110o*. Turn the water off. Replace the stop ring so that the tooth is against the high temperature limit stop. Replace the clip. Justify the handle. *Please know and follow all applicable local plumbing codes when setting the high temperature limit stop. User Instructions Using the Thermostatic Mixer Turn the handle clockwise to make the water cooler. Turn the handle counter-clockwise to make the water warmer. When the safety stop override is at the 12:00 position, the output water is 100o F, the handle will stop. If a user wants water hotter than 100o F, press the safety stop override button and continue turning the handle counter-clockwise. Using the Diverter Pull the lever upward to turn the water on. Pivot the handle to the desired function. There are five functions: Alll-around shower (handshower and 4 lower bodysprays) 4 lower bodysprays 2 upper bodysprays Full-body massage (all 6 bodysprays) Handheld shower Using the 3-Jet Handshower To change spray modes, push the selector lever until the desired spray is achieved. selector lever Rain AIR Balance AIR Whirl AIR Scale Removal The Raindance Air 3-jet handshower incorporates the RubitTM cleaning system. If scale deposits are noticed in the spray channels, turn the water on lightly and rub the spray channels with a finger or a sponge. If scale deposits ar...