Log:
valutazioni - 3, GPA: 3 ( )

Istruzioni per l'uso Axor, Modello TROPIC CADET 2490

Produttore : Axor
File Size : 140.15 kb
File Nome : Install_1970.pdf
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


Towel or sponge remaining water from tank and bowl. b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply! c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases. d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area. NOTE: Mounting surface must be clean and level before new toilet is installed! S A VE FOR USE32 CLOSET FLANGE CLOSET BOLTS 7301102-100 Rev. K A P r oduct names list ed her ein ar e tr ademar ks of A S Amer ica, Inc. FINISHED WALL FINISHED FLOOR SUPPLY AS REQ'D. 12" (305mm) WAX RING SEALANT 54 INSTALL WAX SEAL Invert toilet on floor (cushion to prevent damage), and install wax ring evenly around waste flange (horn), with tapered end of ring facing toilet. Apply a thin bead of sealant around toilet base. POSITION TOILET ON FLANGE a. Unplug floor waste opening and install toilet on closet flange so bolts project through mounting holes. b. Loosely install retainer washers and nuts. Side of washers marked "THIS SIDE UP" must face up! CLOSET BOLT NUT TAPERED WASHER FLANGE INSTALL CLOSET BOLTS Install closet bolts in flange channel, turn 90°, and slide into place 6" (152 mm) apart and parallel to wall. For 4007 Tanks: 12" (305mm) ROUGHING-IN DIMENSIONS: NOTE: Distance from wall to closet flange centerline must be as listed below: © AS America, Inc. 2011 RUBBER GASKET TANK MTG. BOLTS PREINSTALLED 6 7 INSTALL TOILET a. Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until toilet is firmly seated on floor. CAUTION: DO NOT OVERTIGHTEN NUTS OR BASE MAY BE DAMAGED! b. Install caps on washers. (If necessary, cut bolt height to size before installing caps.) c. Smooth off the bead of sealant around base. Remove excess sealant. INSTALL TANK a. Install large rubber gasket over threaded outlet on bottom of tank and lower tank onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening, and tank mounting bolts go through mounting holes. Secure with metal washer/nut combo. b. With tank parallel to wall, alternately tighten nuts until tank is snugged down evenly against bowl surface. CLOSET FLANGE CLOSET BOLT NUTWASHER BOLT CAP WASHER/ NUT COMBO ! ! CAUTION: DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT! For Tanks/Bowls using Speed Connect System (Tank mounting bolts pre-installed). USE INCLUDED TOOL, NUT DRIVER, OR DEEP SOCKET RACHET.* 6 7 INSTALL TOILET a. Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until toilet is firmly seated on floor. CAUTION: DO NOT OVERTIGHTEN NUTS OR BASE MAY BE DAMAGED! b. Install caps on washers. (If necessary, cut bolt height to size before installing caps.) c. Smooth off the bead of sealant around base. Remove excess sealant. INSTALL TANK a. Install large rubber gasket over threaded outlet on bott...

Questo manuale è adatto anche per i modelli :
Plumbing - TROPIC CADET 2492 (140.15 kb)
Plumbing - TROPIC CADET 2455 (140.15 kb)
Plumbing - TROPIC CADET 2455 (140.15 kb)
Plumbing - TROPIC CADET 2457 (140.15 kb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie