valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
When mounted at 34" rim height, the Express® meets ADA, ANSI and UFAS requirements for barrier-free clearances, reaches and controls. Always check local codes and ordinances for compliance. Barrier-free and ADA compliant - juvenile height mounting The SS-2/IR/JUV Express® Lavatory System is compliant with Americans with Disabilities Act (ADA) Accessibility Guidelines for Buildings and Facilities: Building Elements Designed for Children's Use; Final Rule. Infrared sensor and solenoid Each sprayhead is controlled by a separate sensor and solenoid valve, enabling each user to activate a single flow of water. Each valve uses less than half the maximum of hot water allowed by the ANSI/ASHRAE/IES 90A-1980 Standard. Supplies required for installation: • (6) 3/8" wall anchors, bolts and washers to mount frame and bowl to wall (minimum pull-out rating of 1,000 lbs.) • 1/2" NPT hot and cold supply piping • 1-1/2" NPT drain piping • 110 volt electrical outlet for 110/24 VAC plug-in transformer (supplied) 4/24/08 Bradley Corporation • 215-1243 Rev. E; EN 08-805 Express® Lavatory System SS-Series Installation - Obsolete SS-2/IR/STD, SS-2/IR/JUV SS-2/IR/STD Express® Lavatory System Dimensions Standard Height Mounting 38-1/4" (971) 8" (203) 6" (152) 22" (559) 34" (864 50" (1270) 8-1/2" (216) 21" 10" (254) (533) Radius 8" (203) Radius 30" (762) Bradley Corporation • 215-1243 Rev. E; EN 08-805 4/24/08 Express® Lavatory System SS-Series SS-2/IR/STD, SS-2/IR/JUV Installation - Obsolete 11" (279) 38" (965) 34" Standard Height (864) 29" SS-2/IR/STD (737) 9" 4" (229) 6" (102) (152) 11" (279) 34" (864) 30" (762) 25" Juvenile Height (635) SS-2/IR/JUV 4" 9" (102) (229) 6" (152) 4/24/08 Bradley Corporation • 215-1243 Rev. E; EN 08-805 Express® Lavatory System SS-Series Installation - Obsolete SS-2/IR/STD, SS-2/IR/JUV Installation Instructions Step 1: Rough in Note: See Figure 1a below (for Standard Height) and Figure 1b on page 6 (for Juvenile Height) when roughing in the Express®. IMPORTANT: Flush the supply lines before making connections. Debris in supply lines will cause the valves to malfunction. IMPORTANT: Dimensions shown in Figure 1a are for a Standard Height Express® only. 1. Rough in 1/2" NPT hot and cold supply lines through wall at dimensions shown. 2. Rough in 1-1/2" NPT drain waste connection through wall at dimensions shown. (MM) 32" (813) 28-5/8" (727) 25" (635) 11-3/8" (289) 19-5/8" (498) (6) 3/8" WALL ANCHORS WITH MINIMUM PULLOUT RATING OF 1,000 LBS. 23-1/2" (597) 9-3/8" (238) 2-3/4" (70) 13-1/2" (343) 1" (25) 23-1/2" (597) 9-3/8" (238) 3" (76) 1/2" NPT HOT AND COLD SUPPLIES, OR TEMPERED SUPPLY - STUB OUT 2" (50) FROM WALL FINISHED FLOOR CENTERLINE 15-1/4" (387) 1-1/2" NPT DRAIN STUB OUT 2" (50) FROM WALL 110 Volt GFCI ELECTRICAL OUTLET Figure 1a SS-2/IR/STD Express® Lavatory System Dimensions Standard Height Mounting Installation Instructions continue . . . Bradley Corporation • 215-1243 Rev. E; EN 08-805 4/24/08 Express® Lavatory System SS-Series SS-2/IR/STD, SS-2/IR/JUV Installation - Obsolete SS-2/IR/JUV Express® Lavatory System Dimensions Juvenile Height Mounting 23-1/2" 23-1/2" (597) (597) 9-3/8" 9-3/8" (238) (238) (MM) 13-1/2" 1" (25) (343) 2-3/4" 3" (70) (76) 1-1/2" NPT DRAIN STUB OUT 2" (50) 1/2" NPT HOT AND 28" FROM WALL COLD SUPPLIES, OR TEMPERED (711) 110 Volt GFCI SUPPLY - STUB 24-5/8" ELECTRICAL OUT 2" (50) FROM (625) OUTLET WALL 21" (533) 15-1/4" 15-5/8" (6) 3/8" WALL ANCHORS FINISHED (387) (397) 11-3/8" WITH MINIMUM PULLFLOOR (289) OUT RATING OF 1,000 LBS. CENTERLINE Figure 1b Installation Instructions continue . . . 4/24/08 Bradley Corporation • 215-1243 Rev. E; EN 08-805 Express® Lavatory System SS-Series Installation - Obsolete SS-2/IR/STD, SS-2/IR/JUV Installation Instructions continued . . . Step 1: Rough in continued . . . IMPORTANT: Turn OFF electrical power to the outlet when installing the Express®. 3. Install the 110 volt GFCI electrical outlet per local code at the location shown in Figure 2. 4. Install (6) 3/8" wall anchors with a minimum pull-out rating of 1,000 lbs. (supplied by installer) at the locations shown in Figures 1a or 1b on pages 5-6. NOTE: The anchors will be used to mount the Express® bowl and frame to the wall. 110 Volt GFCI ELECTRICAL OUTLET Figure 2 1-1/2" NPT DRAIN STUB OUT 1/2" NPT HOT AND COLD SUPPLIES OR TEMPERED SUPPLY - STUB OUT Installation Instructions continue . . . Bradley Corporation • 215-1243 Rev. E; EN 08-805 4/24/08 Express® Lavatory System SS-Series SS-2/IR/STD, SS-2/IR/JUV Installation - Obsolete Installation Instructions continued . . . Step 2: Mounting frame to wall 1. Remove the eight Torx-head screws securing the panel to the frame, and remove the panel (see Figure 3). Note: Scuff panel does not need to be removed. 2. Position the frame against the wall, ensuring that it is level. If necessary, insert shims under the frame until level. Note: When mounted, the Standard and Juvenile Height frames should rest on the floor. IMPORTANT: Anchoring the fram...
Questo manuale è adatto anche per i modelli :Plumbing - SS-2/IR/STD (206.18 kb)