valutazioni - 3, GPA: 4.3 ( )

Produttore : Hans Grohe File Size : 369.46 kb File Nome : Install_4240.pdf Lingua di insegnamento:

CAUTION12Insert SPOUT SHANK (2) through center hole of MOUNTING LEDGE. Make sure that the RUBBER RING (1) is properly seated in RECESSof SPOUT BASE. Assemble RUBBER WASHER (3) and BRASS WASHER (4) onto SHANK (2). From underside of ledge secure SPOUT (6) into position with LOCKNUT (5). SPOUT ASSEMBLY PREPARE TUBE AND TEE ASSEMBLY 4 2 3 1 3 4 Prepare TUBE and TEE ASSEMBLY (1) to fit center to center VALVE (2) location (between 6-1/2" and 12"). If necessary, cut and/or bend TUBING carefully. Make sure tube bend is close to the TEE (1) so that it will not effect the compression joint at the VALVE CONNECTION. Remove COUPLING NUT (3) and FERRULE (4) from each VALVE (2) and slide onto TUBING (5). 5 Flat Blade Screwdriver Adjustable Wrench Channel Locks VALVE inlet is 3/4-inch NPT male. NOTE ROUGHING-IN DIMENSIONS MOUNTING SURFACE Installation Instructions 7420.900 7420.901 Series 7420.920 7420.921 Series Tubing Cutter RECESS 6 1 3 5 2 4 MOUNTING SURFACE 6-1/2" to 12" (165mm to 305mm) Install RUBBER RING (1) into recess of spout base. M 96502 7 REV. 1. 6 Thank you for selecting American-Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-- please read these instructions carefully before you begin. 2-1/4" D. (56mm) D. CROSS HANDLE LEVER HANDLE 7-7/8" (199mm) 7-7/8" (200mm) 4-7/8" (125mm) 3-3/16" (81mm) 2-7/8" (73mm) 6-1/2" to 12" (165mm to 305mm) 2-5/8" D. (66mm) D. 1-1/2 MAX. (38mm) MAX. 1-3/16" MAX. (30mm) MAX. 1-3/16 D. (30mm) D. 3' (76mm) (H) (C) 1-1/8 D. 12 MAX. (305mm) 2-1/16" D. (52mm) D. 1-1/16 D. (27mm) D. 3/4-14 MALEN.P.T. INLETS 8-1/4" (210mm) 9 2 5/16'' MIN. 4 MOUNTING SURFACE 10 11 11 10 1 3 Push TUBING (3) ends into VALVE (4) side outlets. Insert VALVES (4) into mounting holes from underside of ledge. Press TEE (5) onto SPOUT SHANK (6) making certain that the O-RING (7) is properly seated on SHANK (6). Push COUPLING (8) into TEE (5) and attach to SPOUT SHANK (6) and tighten using a 10mm (3/8'') hex wrench. Tighten COUPLING (8) using a 10mm (3/8") Hex wrench. (FOR 7020.900/920) Use COUPLING (8a) for fitting less spray. Install LOCKNUTS (1) and RUBBER WASHERS (2) onto valve shanks. Place RUBBER RING (10) into ESCUTCHEON ADAPTERS (9) and thread onto valves until snug against internal stop. Tighten LOCKNUT (1) with WRENCH supplied to secure VALVE (4) position. Slide FERRULE (12) and COUPLING NUT (13) to outlet of VALVE (4) and tighten COUPLING NUT (13) firmly. Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of right VALVE using appropriate connector. VALVE ASSEMBLY HOT COLD 12 4 13 7 6 8a 8 5 13 12 3 4 MOUNTING SURFACE Thread of VALVE BODY (4) should extend at least 5/16 inch above MOUNTING SURFACE (11). If necessary, adjust LOCKNUT (1). 10 9 9 M965027 REV.1.6 Wrench 4 INSTALL HANDLES 5 SERVICE 2 90° To change direction of handle rotation, proceed as follows: Turn valve to OFF position. Unthread HANDLE BASE (1) from DECK ADAPTER (2). Pull HANDLE ASSEMBLY ...

Scarica la tua

Per scaricare, digitare 2 cifre :